Cisco 7600 SIP 200 Hardware Installation Guide - Page 89

-Port OC-192c/STM-64 POS/RPR XFP SPA Interface Specifications, 1-Port OC-192c/STM-64 POS/RPR XFP

Get Cisco 7600 SIP 200 - SPA Interface Processor 200 PDF manuals and user guides
UPC - 746320961286
View all Cisco 7600 SIP 200 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 89 highlights

Chapter 3 Overview: Cisco 7600 Series Router Shared Port Adapters 1-Port OC-192c/STM-64 POS/RPR XFP SPA Overview Table 3-20 LED Label ACTIVE STATUS 1-Port OC-192c/STM-64 POS/RPR XFP SPA LEDs (continued) Color Off Green Amber Off Green Amber State Off On On Off On On Meaning Port is not enabled by software. Port is enabled by software, and loopback is off. Port is enabled by software, and loopback is on. SPA power off. SPA is ready and operational. SPA power is on and good, and the SPA is being configured. 1-Port OC-192c/STM-64 POS/RPR XFP SPA Interface Specifications The framer processes incoming and outgoing SONET or SDH frames. The framer operates at OC-192c/STM-64 line rates (9.95 Gbps). Packet data is transported with a user-configured encapsulation (such as Point-to-Point Protocol [PPP]) and is mapped into the STS-192c/STM-64 frame. The 1-Port OC-192c/STM-64 POS/RPR XFP SPA interface is compliant with the following RFCs: • RFC 1662, PPP in HDLC-like Framing • RFC 2615, PPP over SONET/SDH For information on SNMP MIB support, see "Implementing SNMP on Cisco IOS XR Software" in Cisco IOS XR System Management Configuration Guide. 1-Port OC-192c/STM-64 POS/RPR XFP SPA Optical Transceiver Modules, Connectors, and Cables The 1-Port OC-192c/STM-64 POS/RPR XFP SPA uses a single-mode, 9.95 Gbps, OC-192c optical fiber (SONET STS-192c or SDH STM-64) optical transceiver module for SONET and SDH connection to the network. The 1-Port OC-192c/STM-64 POS/RPR XFP SPA supports the following types of optical transceiver module: • Single-mode short-reach (SR) XFP module-XFP-10GLR-OC192SR • Single-mode intermediate-reach (IR) XFP module-XFP-10GER-OC192IR • Single-mode very-long reach XFP module-XFP-10GZR-OC192LR Cisco Systems qualifies the optics that are approved for use with its SPAs. As of, the above-listed XFPs are the only optical transceiver modules qualified for use. Use a single-mode optical fiber that has a modal-field diameter of 8.7 ±0.5 microns (nominal diameter is approximately 10/125 microns) to connect your router to a network. OL-5052-14 Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide 3-43

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
3-43
Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide
OL-5052-14
Chapter 3
Overview: Cisco 7600 Series Router Shared Port Adapters
1-Port OC-192c/STM-64 POS/RPR XFP SPA Overview
1-Port OC-192c/STM-64 POS/RPR XFP SPA Interface Specifications
The framer processes incoming and outgoing SONET or SDH frames. The framer operates at
OC-192c/STM-64 line rates (9.95 Gbps).
Packet data is transported with a user-configured encapsulation (such as Point-to-Point Protocol [PPP])
and is mapped into the STS-192c/STM-64 frame.
The 1-Port OC-192c/STM-64 POS/RPR XFP SPA interface is compliant with the following RFCs:
•
RFC 1662,
PPP in HDLC-like Framing
•
RFC 2615,
PPP over SONET/SDH
For information on SNMP MIB support, see “Implementing SNMP on Cisco IOS XR Software” in
Cisco IOS XR System Management Configuration Guide
.
1-Port OC-192c/STM-64 POS/RPR XFP SPA Optical Transceiver Modules,
Connectors, and Cables
The 1-Port OC-192c/STM-64 POS/RPR XFP SPA uses a single-mode, 9.95 Gbps, OC-192c optical fiber
(SONET STS-192c or SDH STM-64) optical transceiver module for SONET and SDH connection to the
network.
The 1-Port OC-192c/STM-64 POS/RPR XFP SPA supports the following types of optical transceiver
module:
•
Single-mode short-reach (SR) XFP module—XFP-10GLR-OC192SR
•
Single-mode intermediate-reach (IR) XFP module—XFP-10GER-OC192IR
•
Single-mode very-long reach XFP module—XFP-10GZR-OC192LR
Cisco Systems qualifies the optics that are approved for use with its SPAs. As of, the above-listed XFPs
are the only optical transceiver modules qualified for use.
Use a single-mode optical fiber that has a modal-field diameter of 8.7 ±0.5 microns (nominal diameter
is approximately 10/125 microns) to connect your router to a network.
ACTIVE
Off
Off
Port is not enabled by software.
Green
On
Port is enabled by software, and loopback is off.
Amber
On
Port is enabled by software, and loopback is on.
STATUS
Off
Off
SPA power off.
Green
On
SPA is ready and operational.
Amber
On
SPA power is on and good, and the SPA is being configured.
Table 3-20
1-Port OC-192c/STM-64 POS/RPR XFP SPA LEDs (continued)
LED Label
Color
State
Meaning