Creative SB0060 User Guide - Page 91

Sbeset.exe

Get Creative SB0060 - Sound Blaster Live PDF manuals and user guides
UPC - 494180250742
View all Creative SB0060 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 91 highlights

To set SBEMIXER values within the Mixer screen: • At the DOS prompt, type SBEMIXER The interactive editor mode allows you to change the mixer settings with the mouse, , , , or arrow keys. Use the Save button to save the settings for the next session. SBESET.EXE Use SBESET.EXE to manually configure SB resources or disable SB Emulation. By default, SB Emulation in DOS follows the Windows settings. For example, if you disable SB Emulation in Windows, in the next boot to DOS SB Emulation in DOS disabled. Under rare circumstances you may need to manually reconfigure DOS SB Emulation, for example, if there is conflict in DOS before it can boot to Windows. SBESET.EXE is run from the command line. To set SBESET values in the command line: See "Understanding the System Resource Settings" on page B-4 for a list of the possible values. At the DOS prompt, type the SBESET command in a single line. Its syntax is: SBESET [-Axxx] [-Ix] [-Dx] [-Hx] [-Pxxx] [-dx] [-wx] where square brackets [ ] denote optional parameters, and: This Parameter -Axxx -Ix -Dx -Hx -Pxxx -dx -wx Specifies SB interface's base I/O address. IRQ line used by the audio interface. First DMA channel used by the audio interface. Second DMA channel used by the audio interface. MPU-401 UART interface's base I/O address. SB Emulation mode. For x, 1 is Off, 0 is On. Set x to 1 to use the Windows-assigned resource configuration. Set x to 0 to use (your) user-assigned resource configuration. SB Emulation in MS-DOS/ Windows 95/98 B-11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
SB Emulation in MS-DOS/ Windows 95/98
B-11
To set
SBEMIXER
values within the Mixer screen:
•
At the DOS prompt, type
SBEMIXER
The interactive editor mode allows you to change the mixer settings with the mouse, <Tab>,
<PgUp>, <PgDn>, or arrow keys.
Use the Save button to save the settings for the next session.
SBESET.EXE
Use
SBESET.EXE
to manually configure SB resources or disable SB Emulation. By default, SB
Emulation in DOS follows the Windows settings. For example, if you disable SB Emulation in
Windows, in the next boot to DOS SB Emulation in DOS disabled. Under rare circumstances
you may need to manually reconfigure DOS SB Emulation, for example, if there is conflict in
DOS before it can boot to Windows.
SBESET.EXE
is run from the command line.
To set SBESET values in the command line:
At the DOS prompt, type the
SBESET
command in a single line. Its syntax is:
SBESET [-A
xxx
] [-I
x
] [-D
x
] [-H
x
] [-P
xxx
] [-d
x
] [-w
x
]
where square brackets [ ] denote optional parameters, and:
This
Parameter
Specifies
-A
xxx
SB interface’s base I/O address.
-I
x
IRQ line used by the audio interface.
-D
x
First DMA channel used by the audio interface.
-H
x
Second DMA channel used by the audio interface.
-P
xxx
MPU-401 UART interface’s base I/O address.
-d
x
SB Emulation mode. For
x,
1 is Off, 0 is On.
-w
x
Set
x
to 1 to use the Windows-assigned resource configuration.
Set
x
to 0 to use (your) user-assigned resource configuration.
See “Understanding the System
Resource Settings” on page B-4
for a list of the possible values.