Cub Cadet CC30H Riding Lawn Mower Operation Manual - Page 15
H. Parking Brake/speed Control Lever
View all Cub Cadet CC30H Riding Lawn Mower manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 15 highlights
OPERATION CAUTION Prior to operating the riding mower, refer to both Safety Interlock Switches and Starting the Engine in the Operation section of this manual for detailed instructions regarding the Ignition Switch Module and operating the riding mower in REVERSE CAUTION MODE. Ignition Switch Module (If equipped) The ignition switch module has three positions: STOP - The engine and electrical system are turned off. RUN - The riding mower electrical system is energized. START - The starter motor will turn over the engine. Release the key immediately when the engine starts. NOTE: To prevent accidental starting and/or battery discharge, remove key from the ignition switch module when riding mower is not in use. C. FORWARD DRIVE PEDAL (HYDRO RIDING MOWERS) The forward drive pedal is located on the right side of the machine, along the running board. Press the forward drive pedal forward to cause the riding mower to travel forward. Ground speed is also controlled with the forward drive pedal. The further forward the pedal is pivoted, the faster the riding mower will travel. The pedal will return to its original/neutral position when it is not pressed. D. REVERSE DRIVE PEDAL (HYDRO RIDING MOWERS) The reverse drive pedal is located on the right side of the riding mower along the running board. Ground speed is also controlled with the reverse drive pedal. The further downward the pedal is pivoted, the faster the riding mower will travel. The pedal will return to its original/neutral position when it is not pressed. E. BRAKE PEDAL (HYDRO RIDING MOWERS) The brake pedal is located on the left side of the riding mower, along the running board. Depress the pedal all the way down to engage the disc brake and bring the riding mower to a complete stop. NOTE: The brake pedal must be completely depressed to start the engine. Refer to Safety Interlock Switches for more information. F. CLUTCH-BRAKE PEDAL (6-SPEED RIDING MOWERS) The clutch-brake pedal is located on the left side of the riding mower, along the running board. Depress the clutch-brake pedal part way down when slowing the riding mower by changing speeds (refer to parking brake/speed control lever). Depress the pedal all the way down to engage the disc brake and bring the riding mower to a complete stop. NOTE: The clutch-brake pedal must be completely depressed to start the engine. Refer to Safety Interlock Switches section. G. PARKING BRAKE LEVER (HYDRO RIDING MOWERS) To set the parking brake, fully depress the brake pedal. Move the parking brake lever all the way down and into the parking brake position. Release the brake pedal to allow the parking brake to engage. To release the parking brake, depress the brake pedal and move the parking brake lever out of the parking brake position. Release the brake pedal. NOTE: The parking brake must be set if the operator leaves the seat with the engine running or the engine will automatically shut off. H. PARKING BRAKE/SPEED CONTROL LEVER (6-SPEED RIDING MOWERS) To set the parking brake, fully depress the clutch-brake pedal. Move the parking brake/speed control lever all the way down and into the parking brake position. Release the clutch-brake pedal to allow the parking brake to engage. To release the parking brake, depress the clutch-brake pedal and move the parking brake/speed control lever out of the parking brake position into the desired position. Release the clutch-brake pedal. NOTE: The parking brake must be set if the operator leaves the seat with the engine running or the engine will automatically shut off. The speed control lever allows you to regulate the ground speed of the riding mower. To use, depress the clutch-brake pedal and move the parking brake/speed control lever out of the parking brake notch and forward to increase the riding mower's ground speed. When a desired speed has been reached, release the parking brake/speed control lever into an appropriate notch to maintain that speed. To slow the riding mower's ground speed, depress the clutchbrake pedal and move the parking brake/speed control lever rearward and release it into a notch. 15