Dell Dimension 2010 Service Manual - Page 37

Removing an Optical Drive

Get Dell Dimension 2010 PDF manuals and user guides View all Dell Dimension 2010 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 37 highlights

6 Align the screw holes in the Media Card Reader with the screw holes in the FlexBay slot. 7 Replace the two screws that secure the Media Card Reader to the FlexBay slot. NOTE: Ensure that the Media Card Reader is installed before the FlexBay USB cable is connected. 8 Connect the FlexBay USB cable to the Media Card Reader connector on the system board. For the location of the connector, see "System Board Components" on page 8. 9 Replace the front bezel (see "Replacing the Front Bezel" on page 20). 10 Replace the computer cover on both the sides (see "Replacing the Computer Cover" on page 16). 11 Connect your computer and devices to electrical outlets, and then turn them on. Removing an Optical Drive 1 Follow the procedures in "Before You Begin" on page 11. 2 Remove the computer cover from both the sides (see "Removing the Computer Cover" on page 15). 3 Remove the front bezel (see "Removing the Front Bezel" on page 19). 4 Disconnect the power cable and the data cable from the back of the optical drive. NOTE: If you are not replacing the optical drive at this time, disconnect the other end of the data cable from the system board and set it aside. You can use the data cable to install an optical drive at a later time. For the location of the SATA connectors, see "System Board Components" on page 8. Drives 37

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
Drives
37
6
Align the screw holes in the Media Card Reader with the screw holes in the
FlexBay slot.
7
Replace the two screws that secure the Media Card Reader to the FlexBay
slot.
NOTE:
Ensure that the Media Card Reader is installed before the FlexBay
USB cable is connected.
8
Connect the FlexBay USB cable to the Media Card Reader connector on
the system board. For the location of the connector, see "System Board
Components" on page 8.
9
Replace the front bezel (see "Replacing the Front Bezel" on page 20).
10
Replace the computer cover on both the sides (see "Replacing the
Computer Cover" on page 16).
11
Connect your computer and devices to electrical outlets, and then turn
them on.
Removing an Optical Drive
1
Follow the procedures in "Before You Begin" on page11.
2
Remove the computer cover from both the sides (see "Removing the
Computer Cover" on page 15).
3
Remove the front bezel (see "Removing the Front Bezel" on page 19).
4
Disconnect the power cable and the data cable from the back of the
optical drive.
NOTE:
If you are not replacing the optical drive at this time, disconnect the
other end of the data cable from the system board and set it aside. You can
use the data cable to install an optical drive at a later time. For the location of
the SATA connectors, see "System Board Components" on page 8.