Dell Latitude 7350 Detachable Owners Manual - Page 51

Removing the display assembly

Get Dell Latitude 7350 Detachable PDF manuals and user guides View all Dell Latitude 7350 Detachable manuals
Add to My Manuals
Save this manual to your list of manuals

Page 51 highlights

Figure 19. Removing the display assembly Steps 1. Open the kick stand the and the computer turns on automatically. NOTE: The Latitude 7350 Detachable has an automatic power-on feature. The computer powers on when the kick stand is opened. Follow the below steps to ensure that the computer does not power on while the performing replacement procedures. 2. With the kick stand open, shut down the computer using the operating system. 3. Place the computer on a padded surface with the display facing down. 4. CAUTION: Make sure that the computer is turned off before removing the screws. Remove the four screws (M1.6x3) that secure the display assembly to the display-back cover. 5. Push the flat end of a plastic scribe into the release holes below the kick-stand hinges to loosen the display assembly from the display-back cover. 6. Close the kick stand and flip the computer over with the display facing up. 7. Using a plastic scribe, pry open the display assembly from the bottom-left corner. 8. Work your way around the top and remaining sides of the display assembly. 9. Gently flip open the display assembly from the top edge and lay the display-panel assembly face down. CAUTION: Do not pull the display panel away from the computer while the display panel is still connected to the system board. 10. Remove the two screws (M2x3) that secure the display-cable bracket to the system board. 11. Remove the display-cable bracket from the computer. 12. Disconnect the display cable from the connector (eDP) on the system board and remove the display assembly from the computer. 13. Remove the single screw (M1.6x3.4, T5) that secures the battery-cable connector to the interposer board. Removing and installing Field Replaceable Units (FRUs) 51

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
Figure 19. Removing the display assembly
Steps
1.
Open the kick stand the and the computer turns on automatically.
NOTE:
The Latitude 7350 Detachable has an automatic power-on feature. The computer powers on when the kick
stand is opened. Follow the below steps to ensure that the computer does not power on while the performing
replacement procedures.
2.
With the kick stand open, shut down the computer using the operating system.
3.
Place the computer on a padded surface with the display facing down.
4.
CAUTION:
Make sure that the computer is turned off before removing the screws.
Remove the four screws (M1.6x3) that secure the display assembly to the display-back cover.
5.
Push the flat end of a plastic scribe into the release holes below the kick-stand hinges to loosen the display assembly from
the display-back cover.
6.
Close the kick stand and flip the computer over with the display facing up.
7.
Using a plastic scribe, pry open the display assembly from the bottom-left corner.
8.
Work your way around the top and remaining sides of the display assembly.
9.
Gently flip open the display assembly from the top edge and lay the display-panel assembly face down.
CAUTION:
Do not pull the display panel away from the computer while the display panel is still connected to
the system board.
10.
Remove the two screws (M2x3) that secure the display-cable bracket to the system board.
11.
Remove the display-cable bracket from the computer.
12.
Disconnect the display cable from the connector (eDP) on the system board and remove the display assembly from the
computer.
13.
Remove the single screw (M1.6x3.4, T5) that secures the battery-cable connector to the interposer board.
Removing and installing Field Replaceable Units (FRUs)
51