Dell Latitude 7350 Detachable Owners Manual - Page 56

Installing the display cable, Removing the display cable

Get Dell Latitude 7350 Detachable PDF manuals and user guides View all Dell Latitude 7350 Detachable manuals
Add to My Manuals
Save this manual to your list of manuals

Page 56 highlights

Figure 24. Removing the display cable Steps 1. On the back of the display assembly, peel off the large mylar foil that covers both the display-cable connector and touch-module connector: a. Start peeling from the notch indicated by the arrow, being careful not to peel off the touch-module connector underneath. b. Continue peeling the other side of the large mylar foil, until the whole piece can be removed. NOTE: Do not discard the large mylar foil. The large mylar foil is re-useable and is to be re-adhered when the display cable is replaced. 2. Peel off the mylar foil covering the display-cable connector followed by mylar foil covering the touch-module connector. 3. Peel off the display-cable connector (CN1) from the display panel. 4. Open the latch on the touch-module connector and disconnect it from the display assembly. 5. Peel off and remove the display cable from the display assembly. Installing the display cable CAUTION: The information in this installation section is intended for authorized service technicians only. 56 Removing and installing Field Replaceable Units (FRUs)

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
Figure 24. Removing the display cable
Steps
1.
On the back of the display assembly, peel off the large mylar foil that covers both the display-cable connector and
touch-module connector:
a.
Start peeling from the notch indicated by the arrow, being careful not to peel off the touch-module connector
underneath.
b.
Continue peeling the other side of the large mylar foil, until the whole piece can be removed.
NOTE:
Do not discard the large mylar foil. The large mylar foil is re-useable and is to be re-adhered when the display
cable is replaced.
2.
Peel off the mylar foil covering the display-cable connector followed by mylar foil covering the touch-module connector.
3.
Peel off the display-cable connector (CN1) from the display panel.
4.
Open the latch on the touch-module connector and disconnect it from the display assembly.
5.
Peel off and remove the display cable from the display assembly.
Installing the display cable
CAUTION:
The information in this installation section is intended for authorized service technicians only.
56
Removing and installing Field Replaceable Units (FRUs)