Dell Latitude 7350 Detachable Owners Manual - Page 72

Installing the battery

Get Dell Latitude 7350 Detachable PDF manuals and user guides View all Dell Latitude 7350 Detachable manuals
Add to My Manuals
Save this manual to your list of manuals

Page 72 highlights

2. Open the latch and disconnect the HALL-sensor FPC from the connector (Kickstand Detect) on the system board. 3. Carefully peel the docking-connector FPC and HALL-sensor FPC from the battery. 4. For computers with WWAN support: NOTE: Skip to the next step if your computer does not support WWAN. a. Loosen the captive screw (M1.6x2.5) that secures the WWAN-card bracket to the WWAN card. b. Slide and remove the WWAN-card bracket off the WWAN card. c. Disconnect the orange MIMO3 WWAN antenna and blue MIMO2 WWAN antenna cables from the WWAN card. d. Disconnect the green WWAN P-sensor cable from the WWAN card. e. Peel back the mylar on the battery that secures the antenna cables in place. f. Unroute the antenna cables from the clips and routing channels around the left, right and top of the battery. 5. Remove the six screws (M2x3) that secure the battery in place. 6. Remove the battery from the computer. Installing the battery CAUTION: The information in this installation section is intended for authorized service technicians only. Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure. About this task The following images indicate the location of the battery and provides a visual representation of the installation procedure. Figure 40. Installing the battery 72 Removing and installing Field Replaceable Units (FRUs)

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
2.
Open the latch and disconnect the HALL-sensor FPC from the connector (Kickstand Detect) on the system board.
3.
Carefully peel the docking-connector FPC and HALL-sensor FPC from the battery.
4.
For computers with WWAN support:
NOTE:
Skip to the next step if your computer does not support WWAN.
a.
Loosen the captive screw (M1.6x2.5) that secures the WWAN-card bracket to the WWAN card.
b.
Slide and remove the WWAN-card bracket off the WWAN card.
c.
Disconnect the orange MIMO3 WWAN antenna and blue MIMO2 WWAN antenna cables from the WWAN card.
d.
Disconnect the green WWAN P-sensor cable from the WWAN card.
e.
Peel back the mylar on the battery that secures the antenna cables in place.
f.
Unroute the antenna cables from the clips and routing channels around the left, right and top of the battery.
5.
Remove the six screws (M2x3) that secure the battery in place.
6.
Remove the battery from the computer.
Installing the battery
CAUTION:
The information in this installation section is intended for authorized service technicians only.
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
About this task
The following images indicate the location of the battery and provides a visual representation of the installation procedure.
Figure 40. Installing the battery
72
Removing and installing Field Replaceable Units (FRUs)