Dell Latitude 7350 Detachable Owners Manual - Page 57

Docking connector, Removing the docking connector

Get Dell Latitude 7350 Detachable PDF manuals and user guides View all Dell Latitude 7350 Detachable manuals
Add to My Manuals
Save this manual to your list of manuals

Page 57 highlights

Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure. About this task The following images indicate indicates the location of the display cable and provides a visual representation of the installation procedure. Figure 25. Installing the display cable Steps 1. Adhere the display cable to the back of the display assembly. 2. Connect the touch-module connector (CN1) to the display assembly and close the latch. 3. Connect the display-cable connector to the display assembly. 4. Adhere the individual pieces of mylar foil to secure the display-cable connector and the touch-module connector the display panel. 5. Re-adhere the large mylar foil (from the disassembly procedure) to both the display-cable connector and the touch-module connector. Next steps 1. Install the display assembly. 2. Install the SIM-card tray. 3. Follow the procedure in After working inside your computer. Docking connector Removing the docking connector CAUTION: The information in this removal section is intended for authorized service technicians only. Removing and installing Field Replaceable Units (FRUs) 57

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
About this task
The following images indicate indicates the location of the display cable and provides a visual representation of the installation
procedure.
Figure 25. Installing the display cable
Steps
1.
Adhere the display cable to the back of the display assembly.
2.
Connect the touch-module connector (CN1) to the display assembly and close the latch.
3.
Connect the display-cable connector to the display assembly.
4.
Adhere the individual pieces of mylar foil to secure the display-cable connector and the touch-module connector the display
panel.
5.
Re-adhere the large mylar foil (from the disassembly procedure) to both the display-cable connector and the touch-module
connector.
Next steps
1.
Install the
display assembly
.
2.
Install the
SIM-card tray
.
3.
Follow the procedure in
After working inside your computer
.
Docking connector
Removing the docking connector
CAUTION:
The information in this removal section is intended for authorized service technicians only.
Removing and installing Field Replaceable Units (FRUs)
57