Dell Latitude 7350 Detachable Owners Manual - Page 55

Display cable, Removing the display cable

Get Dell Latitude 7350 Detachable PDF manuals and user guides View all Dell Latitude 7350 Detachable manuals
Add to My Manuals
Save this manual to your list of manuals

Page 55 highlights

CAUTION: The pins on the interposer board are very fragile. Avoid contact with the pins on the board and DO NOT allow the pins to come into contact with any substance that may stain or contaminate the pins. Handle the board by lifting and holding from the edges or the sides. 3. Connect the battery-cable connector to the interposer board. 4. Replace the single screw (M1.6x3.4, T5) that secures the battery-cable connector to the interposer board. 5. Connect the display cable to the connector (eDP) on the system board. 6. Align and place the display-cable bracket on the display-cable connector (eDP). 7. Replace the two screws (M2x3) that secure the display-cable bracket to the system board. 8. Gently flip the display assembly onto the computer. 9. Align and slide the bottom of the display assembly into the slots on the computer frame. 10. Gently press along the edges of the display assembly until they snap securely into place. 11. Open the stand. 12. Replace the four screws (M1.6x3) that secure the display assembly to the display-back cover. 13. Close the kick stand. Next steps 1. Install the SIM-card tray. 2. Follow the procedure in After working inside your computer. Display cable Removing the display cable CAUTION: The information in this removal section is intended for authorized service technicians only. Prerequisites 1. Follow the procedure in Before working inside your computer. 2. Remove the SIM-card tray. 3. Remove the display assembly. About this task The following images indicate the location of the display cable and provide a visual representation of the removal procedure. Removing and installing Field Replaceable Units (FRUs) 55

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
CAUTION:
The pins on the interposer board are very fragile. Avoid contact with the pins on the board and DO
NOT allow the pins to come into contact with any substance that may stain or contaminate the pins. Handle
the board by lifting and holding from the edges or the sides.
3.
Connect the battery-cable connector to the interposer board.
4.
Replace the single screw (M1.6x3.4, T5) that secures the battery-cable connector to the interposer board.
5.
Connect the display cable to the connector (eDP) on the system board.
6.
Align and place the display-cable bracket on the display-cable connector (eDP).
7.
Replace the two screws (M2x3) that secure the display-cable bracket to the system board.
8.
Gently flip the display assembly onto the computer.
9.
Align and slide the bottom of the display assembly into the slots on the computer frame.
10.
Gently press along the edges of the display assembly until they snap securely into place.
11.
Open the stand.
12.
Replace the four screws (M1.6x3) that secure the display assembly to the display-back cover.
13.
Close the kick stand.
Next steps
1.
Install the
SIM-card tray
.
2.
Follow the procedure in
After working inside your computer
.
Display cable
Removing the display cable
CAUTION:
The information in this removal section is intended for authorized service technicians only.
Prerequisites
1.
Follow the procedure in
Before working inside your computer
.
2.
Remove the
SIM-card tray
.
3.
Remove the
display assembly
.
About this task
The following images indicate the location of the display cable and provide a visual representation of the removal procedure.
Removing and installing Field Replaceable Units (FRUs)
55