Dell PowerEdge 1955 Configuration Guide - Page 32

Configuring the Switch Using a Serial or Telnet Console, switch-1, switch-1config - blade

Get Dell PowerEdge 1955 PDF manuals and user guides View all Dell PowerEdge 1955 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 32 highlights

Configuring the Switch Using a Serial or Telnet Console To configure the Cisco Catalyst Blade Switch 3030 switch module using the DRAC/MC module, perform the following steps. 1 Log on to the DRAC/MC Telnet or serial interface. 2 To redirect the switch console through the DRAC/MC console, enter the following command: connect switch-x where x is the module slot number on the chassis. For example, if you are connecting to switch module 1, type connect switch-1 3 Enter privileged EXEC mode: switch-1> enable 4 Configure the number of Telnet sessions (lines), and enter line configuration mode: switch-1# line vty 0 15 5 If applicable, enter a Telnet password: switch-1# password password 6 Change to terminal configuration mode: switch-1# configure terminal 7 Change to interface configuration mode, and enter the VLAN number to which the IP information is assigned. The default value is 1. switch-1(config)# interface vlan vlan-id 8 Specify the IP address and subnet mask: switch-1(config-vlan)# ip address ip-address subnet-mask 9 Return to global configuration mode: switch-1(config-vlan)# exit 10 Specify the IP address of the default gateway: switch-1(config)# ip default-gateway ip-address 11 Return to privileged EXEC mode: switch-1(config)# end 12 Verify the IP address: switch-1# show interfaces vlan vlan-id 13 Enter the following command to verify the default gateway IP address: switch-1# show ip redirects 30 General System Configuration

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
30
General System Configuration
Configuring the Switch Using a Serial or Telnet Console
To configure the Cisco Catalyst Blade Switch 3030 switch module using the DRAC/MC module,
perform the following steps.
1
Log on to the DRAC/MC Telnet or serial interface.
2
To redirect the switch console through the DRAC/MC console, enter the following command:
connect
switch-
x
where
x
is the module slot number on the chassis. For example, if you are connecting to
switch module 1, type
connect
switch-1
3
Enter privileged EXEC mode:
switch-1
>
enable
4
C
onfigure the number of Telnet sessions (lines), and enter line configuration mode
:
switch-1#
line vty 0 15
5
If applicable, enter
a Telnet password
:
switch-1#
password
password
6
Change to
terminal configuration mode
:
switch-1#
configure terminal
7
Change to
interface configuration mode, and enter the VLAN number to which the IP
information is assigned. The default value is 1
.
switch-1(config)#
interface vlan
vlan-id
8
Specify the IP address and subnet mask:
switch-1(config-vlan)#
ip address
ip-address subnet-mask
9
Return to
global configuration mode
:
switch-1(config-vlan)#
exit
10
Specify the IP address of the default gateway:
switch-1(config)#
ip default-gateway
ip-address
11
Return to
privileged EXEC mode
:
switch-1(config)#
end
12
V
erify the IP address:
switch-1
#
show interfaces vlan
vlan-id
13
Enter the following command to verify the
default gateway IP address
:
switch-1
#
show ip redirects