Dell PowerEdge C6520 EMC Installation and Service Manual - Page 23

Installing and removing system components, Safety instructions, Before working inside your system

Get Dell PowerEdge C6520 PDF manuals and user guides View all Dell PowerEdge C6520 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 23 highlights

4 Installing and removing system components Topics: • Safety instructions • Before working inside your system • After working inside your system • Recommended tools • Sled • Air shroud • Support bracket • Expansion cards and expansion card risers • LOM riser card • M.2 SSD module • Linking board and PCIe cable • System memory • Processor and heat sink module • Optional OCP card • System battery • System board • Trusted Platform Module Safety instructions CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that are shipped with your product. NOTE: It is recommended that you always use an antistatic mat and antistatic strap while working on components inside the system. NOTE: While replacing faulty storage controller, FC, or NIC card with the same type of card, after you power on the system; the new card automatically updates to the same firmware and configuration of the faulty one. For more information about the Part replacement configuration, see the Lifecycle Controller User's Guide at https://www.dell.com/idracmanuals. Before working inside your system Prerequisites Follow the safety guidelines listed in the Safety instructions. Steps 1. Power off the sled. 2. Remove the sled from the enclosure. Installing and removing system components 23

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
Installing and removing system components
Topics:
•
Safety instructions
•
Before working inside your system
•
After working inside your system
•
Recommended tools
•
Sled
•
Air shroud
•
Support bracket
•
Expansion cards and expansion card risers
•
LOM riser card
•
M.2 SSD module
•
Linking board and PCIe cable
•
System memory
•
Processor and heat sink module
•
Optional OCP card
•
System battery
•
System board
•
Trusted Platform Module
Safety instructions
CAUTION:
Many repairs may only be done by a certified service technician. You should only perform
troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or
telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by
your warranty. Read and follow the safety instructions that are shipped with your product.
NOTE:
It is recommended that you always use an antistatic mat and antistatic strap while working on components inside
the system.
NOTE:
While replacing faulty storage controller, FC, or NIC card with the same type of card, after you power on the
system; the new card automatically updates to the same firmware and configuration of the faulty one. For more information
about the Part replacement configuration, see the
Lifecycle Controller User's Guide
at
.
Before working inside your system
Prerequisites
Follow the safety guidelines listed in the
Safety instructions
.
Steps
1.
Power off the sled.
2.
Remove the sled from the enclosure.
4
Installing and removing system components
23