Dell PowerEdge T140 EMC Installation and Service Manual - Page 39

Recommended tools, System cover, Removing the system cover

Get Dell PowerEdge T140 PDF manuals and user guides View all Dell PowerEdge T140 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 39 highlights

Recommended tools You need the following tools to perform the removal and installation procedures: • Phillips #1 screwdriver • Phillips #2 screwdriver • Torx #T15 screwdriver • 5mm hex nut screwdriver • Plastic scribe • Wrist grounding strap connected to the ground • ESD mat System cover Removing the system cover Prerequisites 1. Follow the safety guidelines listed in Safety instructions. 2. Power off the system and all attached peripherals. 3. Disconnect the system from the electrical outlet and peripherals. 4. Place the system on a flat, stable surface. NOTE: Ensure that the lock on the side of the system cover is unlocked. Steps Lift the cover release latch and remove the system cover. Figure 9. Removing the system cover Next steps 1. Replace the system cover. PowerEdge T140 installing and removing system components 39

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
Recommended tools
You need the following tools to perform the removal and installation procedures:
•
Phillips #1 screwdriver
•
Phillips #2 screwdriver
•
Torx #T15 screwdriver
•
5mm hex nut screwdriver
•
Plastic scribe
•
Wrist grounding strap connected to the ground
•
ESD mat
System cover
Removing the system cover
Prerequisites
1.
Follow the safety guidelines listed in
Safety instructions
.
2.
Power off the system and all attached peripherals.
3.
Disconnect the system from the electrical outlet and peripherals.
4.
Place the system on a flat, stable surface.
NOTE:
Ensure that the lock on the side of the system cover is unlocked.
Steps
Lift the cover release latch and remove the system cover.
Figure 9. Removing the system cover
Next steps
1.
Replace the system cover
.
PowerEdge T140 installing and removing system components
39