Dell PowerEdge T140 EMC Installation and Service Manual - Page 48

Removing the optical drive

Get Dell PowerEdge T140 PDF manuals and user guides View all Dell PowerEdge T140 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 48 highlights

Figure 19. Installing the optical drive filler into the front bezel 2. On the optical drive cage, hold the tabs on the optical drive filler and push the optical drive filler into the optical drive cage. Figure 20. Installing the optical drive filler into the optical drive cage Next steps 1. Install the front bezel. 2. Follow the procedure that is listed in After working inside your system. Removing the optical drive Prerequisites 1. Follow the safety guidelines listed in Safety instructions. 2. Follow the procedure listed in Before working inside your system. 3. Remove the front bezel. 4. Disconnect the power and data cables from the back of the optical drive. NOTE: Ensure that you note the routing of the power and data cable on the side of the system as you remove them from the system board and drive . Steps 1. To release the optical drive, press and push the release tab toward the front of the system. 48 PowerEdge T140 installing and removing system components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
Figure 19. Installing the optical drive filler into the front bezel
2.
On the optical drive cage, hold the tabs on the optical drive filler and push the optical drive filler into the optical drive cage.
Figure 20. Installing the optical drive filler into the optical drive cage
Next steps
1.
Install the front bezel
.
2.
Follow the procedure that is listed in
After working inside your system
.
Removing the optical drive
Prerequisites
1.
Follow the safety guidelines listed in
Safety instructions
.
2.
Follow the procedure listed in
Before working inside your system
.
3.
Remove the front bezel
.
4.
Disconnect the power and data cables from the back of the optical drive.
NOTE:
Ensure that you note the routing of the power and data cable on the side of the system as you remove them
from the system board and drive .
Steps
1.
To release the optical drive, press and push the release tab toward the front of the system.
48
PowerEdge T140 installing and removing system components