Dell PowerEdge T140 EMC Installation and Service Manual - Page 61

Installing an integrated storage controller card

Get Dell PowerEdge T140 PDF manuals and user guides View all Dell PowerEdge T140 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 61 highlights

Figure 32. Removing the integrated storage controller card 3. If you are not replacing the integrated storage controller card, install a filler bracket. NOTE: Installing the filler bracket for integrated storage controller card is similar to installing the filler bracket under, removing a PCIe expansion card section. Next steps 1. Replace the integrated storage controller card. Installing an integrated storage controller card Prerequisites 1. Follow the safety guidelines listed in Safety instructions. 2. Follow the procedure that is listed in Before working inside your system. Steps 1. If you are installing a new card, remove the filler bracket by performing the following steps: a. Open the blue expansion card retention latch lock. b. Slide the filler bracket out of the system. NOTE: Removing the filler bracket for integrated storage controller card is similar to removing the filler bracket under, installing a PCIe expansion card section. NOTE: Store this bracket for future use. Filler brackets must be installed in empty expansion-card slots to maintain FCC certification of the system. The brackets also keep dust and dirt out of the system and aid in proper cooling and airflow inside the system. 2. Hold the storage controller card by the edges, and align the connector on the card with the connector on the system board. 3. Lower the card into the system until the card is firmly seated. 4. Close the expansion card retention latch by pushing the latch up until the latch snaps into place. PowerEdge T140 installing and removing system components 61

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
Figure 32. Removing the integrated storage controller card
3.
If you are not replacing the integrated storage controller card, install a filler bracket.
NOTE:
Installing the filler bracket for integrated storage controller card is similar to installing the filler bracket
under,
removing a PCIe expansion card section
.
Next steps
1.
Replace the integrated storage controller card
.
Installing an integrated storage controller card
Prerequisites
1.
Follow the safety guidelines listed in
Safety instructions
.
2.
Follow the procedure that is listed in
Before working inside your system
.
Steps
1.
If you are installing a new card, remove the filler bracket by performing the following steps:
a.
Open the blue expansion card retention latch lock.
b.
Slide the filler bracket out of the system.
NOTE:
Removing the filler bracket for integrated storage controller card is similar to removing the filler bracket
under,
installing a PCIe expansion card section
.
NOTE:
Store this bracket for future use. Filler brackets must be installed in empty expansion-card slots to
maintain FCC certification of the system. The brackets also keep dust and dirt out of the system and aid in
proper cooling and airflow inside the system.
2.
Hold the storage controller card by the edges, and align the connector on the card with the connector on the system board.
3.
Lower the card into the system until the card is firmly seated.
4.
Close the expansion card retention latch by pushing the latch up until the latch snaps into place.
PowerEdge T140 installing and removing system components
61