Dell PowerEdge T140 EMC Installation and Service Manual - Page 80

Installing the TPM, Initializing TPM for BitLocker users, Initializing the TPM 1.2 for TXT users

Get Dell PowerEdge T140 PDF manuals and user guides View all Dell PowerEdge T140 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 80 highlights

Installing the TPM Steps 1. To install the TPM, align the edge connectors on the TPM with the slot on the TPM connector. 2. Insert the TPM into the TPM connector such that the plastic rivet aligns with the slot on the system board. 3. Press the plastic rivet until the rivet snaps into place. 4. Replace the screw that secures the TPM to the system board. Figure 53. Installing the TPM Next steps 1. Replace the system board. 2. Follow the procedure listed in After working inside your system. 3. To verify if the memory module has been installed properly, press F2 and navigate to System Setup Main Menu > System BIOS > Memory Settings. In the Memory Settings screen, the System Memory Size must reflect the updated capacity of the installed memory. 4. If the value is incorrect, one or more of the memory modules may not be installed properly. Ensure that the memory module is firmly seated in the memory module socket. 5. Run the system memory test in system diagnostics. Initializing TPM for BitLocker users Steps 1. Initialize the TPM. For more information, see initializing the TPM for Intel TXT users. 2. The TPM Status changes to Enabled, Activated. Initializing the TPM 1.2 for TXT users Steps 1. While booting your system, press F2 to enter System Setup. 2. On the System Setup Main Menu screen, click System BIOS > System Security Settings. 3. From the TPM Security option, select On with Preboot Measurements. 4. From the TPM Command option, select Activate. 5. Save the settings. 6. Restart your system. 7. Enter System Setup again. 8. On the System Setup Main Menu screen, click System BIOS > System Security Settings. 9. From the Intel TXT option, select On. 80 PowerEdge T140 installing and removing system components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
Installing the TPM
Steps
1.
To install the TPM, align the edge connectors on the TPM with the slot on the TPM connector.
2.
Insert the TPM into the TPM connector such that the plastic rivet aligns with the slot on the system board.
3.
Press the plastic rivet until the rivet snaps into place.
4.
Replace the screw that secures the TPM to the system board.
Figure 53. Installing the TPM
Next steps
1.
Replace the system board
.
2.
Follow the procedure listed in
After working inside your system
.
3.
To verify if the memory module has been installed properly, press F2 and navigate to
System Setup Main Menu > System BIOS >
Memory Settings
. In the
Memory Settings
screen, the System Memory Size must reflect the updated capacity of the installed
memory.
4.
If the value is incorrect, one or more of the memory modules may not be installed properly. Ensure that the memory module is firmly
seated in the memory module socket.
5.
Run the system memory test in system diagnostics.
Initializing TPM for BitLocker users
Steps
1.
Initialize the TPM.
For more information, see
initializing the TPM for Intel TXT users
.
2.
The
TPM Status
changes to
Enabled, Activated
.
Initializing the TPM 1.2 for TXT users
Steps
1.
While booting your system, press F2 to enter System Setup.
2.
On the
System Setup Main Menu
screen, click
System BIOS
>
System Security Settings
.
3.
From the
TPM Security
option, select
On with Preboot Measurements
.
4.
From the
TPM Command
option, select
Activate
.
5.
Save the settings.
6.
Restart your system.
7.
Enter
System Setup
again.
8.
On the
System Setup Main Menu
screen, click
System BIOS
>
System Security Settings
.
9.
From the
Intel TXT
option, select
On
.
80
PowerEdge T140 installing and removing system components