Dell PowerEdge T140 EMC Installation and Service Manual - Page 65

Processor and heat sink, Removing the heat sink module

Get Dell PowerEdge T140 PDF manuals and user guides View all Dell PowerEdge T140 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 65 highlights

Figure 37. Installing the M.2 SSD module Next steps 1. Install the BOSS card. NOTE: The procedure to install the BOSS card is similar to removing an expansion card. 2. Follow the procedure listed in the After working inside your system. Processor and heat sink Removing the heat sink module Prerequisites WARNING: The heat sink may be hot to touch for some time after the system has been powered off. Allow the heat sink to cool before removing it. 1. Follow the safety guidelines listed in Safety instructions. 2. Follow the procedure that is listed in Before working inside your system. Steps 1. Disconnect the heat sink fan power cable connector from the connector on the system board. 2. Using a Phillips #2 screwdriver, loosen the screws on the heat sink in the order following: a. Partially loosen the first screw (approximately 3 turns). b. Loosen the diagonally opposite screw completely. c. Return to the first screw and loosen it completely. d. Repeat the procedure for the remaining two screws. 3. Lift the heat sink away from the system. PowerEdge T140 installing and removing system components 65

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
Figure 37. Installing the M.2 SSD module
Next steps
1.
Install the BOSS card.
NOTE:
The procedure to install the BOSS card is similar to removing an expansion card.
2.
Follow the procedure listed in the
After working inside your system
.
Processor and heat sink
Removing the heat sink module
Prerequisites
WARNING:
The heat sink may be hot to touch for some time after the system has been powered off. Allow the heat sink
to cool before removing it.
1.
Follow the safety guidelines listed in
Safety instructions
.
2.
Follow the procedure that is listed in
Before working inside your system
.
Steps
1.
Disconnect the heat sink fan power cable connector from the connector on the system board.
2.
Using a Phillips #2 screwdriver, loosen the screws on the heat sink in the order following:
a.
Partially loosen the first screw (approximately 3 turns).
b.
Loosen the diagonally opposite screw completely.
c.
Return to the first screw and loosen it completely.
d.
Repeat the procedure for the remaining two screws.
3.
Lift the heat sink away from the system.
PowerEdge T140 installing and removing system components
65