Dell PowerEdge T140 EMC Installation and Service Manual - Page 42

Drives, Removing a 3.5-inch drive carrier from the drive bay

Get Dell PowerEdge T140 PDF manuals and user guides View all Dell PowerEdge T140 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 42 highlights

Figure 12. Installing the front bezel Next steps 1. Follow the procedure that is listed in After working inside your system. Drives Removing a 3.5-inch drive carrier from the drive bay Prerequisites 1. Follow the safety guidelines listed in Safety instructions. 2. Follow the procedure that is listed in Before working inside your system. 3. Disconnect the power and data cables from the drive carrier in the drive bay. 4. Using the management software, prepare the drive for removal. Power off the system completely and unplug cables before remove the drive. For more information, see the www.dell.com/storagecontrollermanuals. CAUTION: Before attempting to remove or install a drive while the system is running, see the documentation for the storage controller card to ensure that the host adapter is configured correctly to support drive removal and insertion. CAUTION: Mixing drive carriers from previous generations of PowerEdge servers is not supported. NOTE: To prevent data loss, ensure that your operating system supports drive installation. See the documentation supplied with your operating system. Steps Press the retention clips and lift the drive carrier out from the drive bay. 42 PowerEdge T140 installing and removing system components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
Figure 12. Installing the front bezel
Next steps
1.
Follow the procedure that is listed in
After working inside your system
.
Drives
Removing a 3.5-inch drive carrier from the drive bay
Prerequisites
1.
Follow the safety guidelines listed in
Safety instructions
.
2.
Follow the procedure that is listed in
Before working inside your system
.
3.
Disconnect the power and data cables from the drive carrier in the drive bay.
4.
Using the management software, prepare the drive for removal. Power off the system completely and unplug cables before remove
the drive. For more information, see the
www.dell.com/storagecontrollermanuals
.
CAUTION:
Before attempting to remove or install a drive while the system is running, see the documentation for the
storage controller card to ensure that the host adapter is configured correctly to support drive removal and
insertion.
CAUTION:
Mixing drive carriers from previous generations of PowerEdge servers is not supported.
NOTE:
To prevent data loss, ensure that your operating system supports drive installation. See the documentation
supplied with your operating system.
Steps
Press the retention clips and lift the drive carrier out from the drive bay.
42
PowerEdge T140 installing and removing system components