Dell PowerEdge T140 EMC Installation and Service Manual - Page 56

Optional internal USB memory key, Replacing the optional internal USB memory key, Expansion cards

Get Dell PowerEdge T140 PDF manuals and user guides View all Dell PowerEdge T140 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 56 highlights

Figure 27. Installing a cooling fan Next steps 1. Follow the procedure that is listed in After working inside your system. Optional internal USB memory key NOTE: To locate the internal USB port on the system board, see the System board jumpers and connectors section. Replacing the optional internal USB memory key Prerequisites CAUTION: To avoid interference with other components in the server, the maximum permissible dimensions of the USB memory key: 15.9 mm width x 57.15 mm length x 7.9 mm height. 1. Follow the safety guidelines listed in the Safety instructions. 2. Follow the procedure listed in the Before working inside your system. Steps 1. Locate the USB port or USB memory key on the system board. To locate the USB port, see the System board jumper and connectors section. 2. If installed, remove the USB memory key from the USB port. 3. Insert the replacement USB memory key into the USB port. Next steps 1. Follow the procedure that is listed in After working inside your system. 2. While booting, press F2 to enter System Setup and verify that the system detects the USB memory key. Expansion cards NOTE: A System Event Log (SEL) event is logged if an expansion card riser is not supported or missing. It does not prevent your system from turning on. However, if a F1/F2 pause occurs with an error message, see Troubleshooting 56 PowerEdge T140 installing and removing system components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
Figure 27. Installing a cooling fan
Next steps
1.
Follow the procedure that is listed in
After working inside your system
.
Optional internal USB memory key
NOTE:
To locate the internal USB port on the system board, see the
System board jumpers and connectors
section.
Replacing the optional internal USB memory key
Prerequisites
CAUTION:
To avoid interference with other components in the server, the maximum permissible dimensions of the USB
memory key: 15.9 mm width x 57.15 mm length x 7.9 mm height.
1.
Follow the safety guidelines listed in the
Safety instructions
.
2.
Follow the procedure listed in the
Before working inside your system
.
Steps
1.
Locate the USB port or USB memory key on the system board.
To locate the USB port, see the
System board jumper and connectors
section.
2.
If installed, remove the USB memory key from the USB port.
3.
Insert the replacement USB memory key into the USB port.
Next steps
1.
Follow the procedure that is listed in
After working inside your system
.
2.
While booting, press F2 to enter System Setup and verify that the system detects the USB memory key.
Expansion cards
NOTE:
A System Event Log (SEL) event is logged if an expansion card riser is not supported or missing. It does not
prevent your system from turning on. However, if a F1/F2 pause occurs with an error message, see
Troubleshooting
56
PowerEdge T140 installing and removing system components