Dell PowerEdge T140 EMC Installation and Service Manual - Page 55

Installing a cooling fan

Get Dell PowerEdge T140 PDF manuals and user guides View all Dell PowerEdge T140 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 55 highlights

Figure 26. Removing the cooling fan Next steps 1. Replace the cooling fan. Installing a cooling fan Prerequisites CAUTION: Do not remove or install the cooling fan by holding the blades. 1. Follow the safety guidelines listed in Safety instructions. 2. Follow the procedure that is listed in Before working inside your system. Steps 1. Hold the cooling fan by the sides with the cable end facing the bottom of the system. 2. Align the four grommets on the system with the four holes on the sides of the cooling fan. NOTE: It is recommended to first install the lower two grommets. 3. Pass the grommets through the corresponding holes on the cooling fan. 4. Stretch the grommets and push the cooling fan toward the system until it is secured in place. 5. Connect the cooling fan power cable to the connector on the system board. PowerEdge T140 installing and removing system components 55

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
Figure 26. Removing the cooling fan
Next steps
1.
Replace the cooling fan
.
Installing a cooling fan
Prerequisites
CAUTION:
Do not remove or install the cooling fan by holding the blades.
1.
Follow the safety guidelines listed in
Safety instructions
.
2.
Follow the procedure that is listed in
Before working inside your system
.
Steps
1.
Hold the cooling fan by the sides with the cable end facing the bottom of the system.
2.
Align the four grommets on the system with the four holes on the sides of the cooling fan.
NOTE:
It is recommended to first install the lower two grommets.
3.
Pass the grommets through the corresponding holes on the cooling fan.
4.
Stretch the grommets and push the cooling fan toward the system until it is secured in place.
5.
Connect the cooling fan power cable to the connector on the system board.
PowerEdge T140 installing and removing system components
55