Dell PowerEdge T140 EMC Installation and Service Manual - Page 87

If you assign a new system and/or setup password with the jumper on pins 4 and 6

Get Dell PowerEdge T140 PDF manuals and user guides View all Dell PowerEdge T140 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 87 highlights

3. Move the jumper on the system board jumper from pins 2 and 4 to pins 4 and 6. 4. Install the system cover. The existing passwords are not disabled (erased) until the system boots with the jumper on pins 4 and 6. However, before you assign a new system and/or setup password, you must move the jumper back to pins 2 and 4. NOTE: If you assign a new system and/or setup password with the jumper on pins 4 and 6, the system disables the new password(s) the next time it boots. 5. Reconnect the system to its electrical outlet and power on the system, including any attached peripherals. 6. Power off the system, including any attached peripherals, and disconnect the system from the electrical outlet. 7. Remove the system cover. 8. Move the jumper on the system board jumper from pins 4 and 6 to pins 2 and 4. 9. Install the system cover. 10. Reconnect the system to its electrical outlet and power on the system, including any attached peripherals. 11. Assign a new system and/or setup password. Jumpers and connectors 87

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
3.
Move the jumper on the system board jumper from pins 2 and 4 to pins 4 and 6.
4.
Install the system cover.
The existing passwords are not disabled (erased) until the system boots with the jumper on pins 4 and 6. However, before you assign
a new system and/or setup password, you must move the jumper back to pins 2 and 4.
NOTE:
If you assign a new system and/or setup password with the jumper on pins 4 and 6, the system disables the
new password(s) the next time it boots.
5.
Reconnect the system to its electrical outlet and power on the system, including any attached peripherals.
6.
Power off the system, including any attached peripherals, and disconnect the system from the electrical outlet.
7.
Remove the system cover.
8.
Move the jumper on the system board jumper from pins 4 and 6 to pins 2 and 4.
9.
Install the system cover.
10.
Reconnect the system to its electrical outlet and power on the system, including any attached peripherals.
11.
Assign a new system and/or setup password.
Jumpers and connectors
87