Dell PowerEdge T140 EMC Installation and Service Manual - Page 58

Steps, Next steps, Removing a PCIe expansion card, Installing the filler bracket

Get Dell PowerEdge T140 PDF manuals and user guides View all Dell PowerEdge T140 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 58 highlights

3. Disconnect any cables that are connected to the expansion card. Steps 1. Press the blue expansion card retention latch and push down the latch to open it. 2. Holding the card by its edge, pull the card to disengage it from the connector and lift the card out of the system. Figure 28. Removing a PCIe expansion card 3. If you are not replacing the expansion card, install a filler bracket by performing the following steps: a. Align the slot on the filler bracket with the tab on the expansion card slot. b. Align the filler bracket with the slot on the system. c. Push the filler bracket downward until firmly seated. d. Close the expansion card retention latch. Figure 29. Installing the filler bracket Next steps 1. Replace the expansion card. 58 PowerEdge T140 installing and removing system components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
3.
Disconnect any cables that are connected to the expansion card.
Steps
1.
Press the blue expansion card retention latch and push down the latch to open it.
2.
Holding the card by its edge, pull the card to disengage it from the connector and lift the card out of the system.
Figure 28. Removing a PCIe expansion card
3.
If you are not replacing the expansion card, install a filler bracket by performing the following steps:
a.
Align the slot on the filler bracket with the tab on the expansion card slot.
b.
Align the filler bracket with the slot on the system.
c.
Push the filler bracket downward until firmly seated.
d.
Close the expansion card retention latch.
Figure 29. Installing the filler bracket
Next steps
1.
Replace the expansion card
.
58
PowerEdge T140 installing and removing system components