Dell PowerEdge T140 EMC Installation and Service Manual - Page 70

Installing the power supply unit

Get Dell PowerEdge T140 PDF manuals and user guides View all Dell PowerEdge T140 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 70 highlights

Figure 43. Removing the PSU Next steps 1. Replace the PSU. Installing the power supply unit Prerequisites 1. Follow the safety guidelines listed in Safety instructions . 2. Follow the procedure listed in Before working inside your system. Steps 1. While replacing a faulty PSU, you may require to bundle the P3 cable. The P3 cable in the PSU connects to the GPU. The PowerEdge T140 system does not support GPU and hence the P3 cable is required to be bundled to avoid system board damage. Follow the below steps to bundle the P3 cable: CAUTION: Connecting the PSU P3 cable to any of the connectors on the system board may result in system board damage. a. Bundle the P3 cable providing equal interval spaces between the smaller cable ties. NOTE: Ensure to align the connector head closer to the middle. b. Secure the P3 cable using the larger cable tie. c. Leaving 10 mm of the larger cable tie, snip the excess cable tie. 70 PowerEdge T140 installing and removing system components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
Figure 43. Removing the PSU
Next steps
1.
Replace the PSU
.
Installing the power supply unit
Prerequisites
1.
Follow the safety guidelines listed in
Safety instructions
.
2.
Follow the procedure listed in
Before working inside your system
.
Steps
1.
While replacing a faulty PSU, you may require to bundle the P3 cable. The P3 cable in the PSU connects to the GPU. The PowerEdge
T140 system does not support GPU and hence the P3 cable is required to be bundled to avoid system board damage. Follow the below
steps to bundle the P3 cable:
CAUTION:
Connecting the PSU P3 cable to any of the connectors on the system board may result in system board
damage.
a.
Bundle the P3 cable providing equal interval spaces between the smaller cable ties.
NOTE:
Ensure to align the connector head closer to the middle.
b.
Secure the P3 cable using the larger cable tie.
c.
Leaving 10 mm of the larger cable tie, snip the excess cable tie.
70
PowerEdge T140 installing and removing system components