Dewalt DXPW3400PR Instruction Manual - Page 16

Alternate Manual Mode, Without Battery

Get Dewalt DXPW3400PR PDF manuals and user guides View all Dewalt DXPW3400PR manuals
Add to My Manuals
Save this manual to your list of manuals

Page 16 highlights

English 15. Place the engine ON/OFF switch 27 in the ON position. Fig. Q ON OFF 27 ENGINE 16. Press the ON/STOP button 28 for 2 seconds. The green READY light will illuminate. The yellow WATER FLOW light should also illuminate to verify the water is connected properly and turned on. Fig. R  DANGER: Risk of injury from spray. Ensure the spring loaded trigger lock 16 is moved forward to the locked position, when the spray gun is not in use to prevent accidental spraying. Alternate Manual Mode Start-up Procedure (Without Battery) (Fig. A, T-Z) 1. In a well-ventilated outdoor area, add fresh, high-quality, unleaded gasoline with a pump octane rating of 86 or higher. Do not overfill. Wipe up spilled fuel before starting the engine. Refer to engine instruction manual for correct procedure. IMPORTANT: Ethanol Shield™ (sold separately) is a fuel stabilizer that helps eliminate and prevent ethanol related problems in power equipment. Follow the instructions on the container and add to the gasoline. 28 17. When the green system ready light illuminates, squeeze the spray gun trigger to start the engine. After squeezing the spray gun trigger it will take approximately 3 seconds for engine to start. After the engine has started, the water flow will begin and the yellow water flow light will illuminate. See the PRESSUREADY® Fault Codes Table in the Troubleshooting section for more information. NOTE: The spray gun is equipped with a spring loaded trigger lock 16 . Manually release trigger lock as shown in Fig. S. Fig. S 16  WARNING: Risk of unsafe operation. Stand on a stable surface and grip spray gun/wand firmly with both hands. Expect the spray gun/wand to kickback when triggered. 18. When spray gun trigger is released, water flow will stop immediately and the engine will shut off in approximately 10 seconds. Ensure spring loaded trigger lock is moved forward into the locked position. 19. To restart pressure washer, manually release trigger lock and squeeze the spray gun trigger and the engine will restart. Note that it will take approximately 3 seconds for engine to start after squeezing spray gun trigger. After the engine has started, the water flow will begin. NOTICE: Use of fuels with greater than 10% ethanol are not approved for use in this product per EPA regulations and will damage the unit and void the warranty. 2. Check engine oil level. Refer to the engine instruction manual for correct procedure. NOTICE: The engine is shipped without oil. Before starting engine, add the oil provided. Damage to the engine will occur if the engine is run without oil, this damage will not be covered under warranty. 3. Place the engine ON/OFF switch 27 in the ON position. Fig. T ON OFF 27 ENGINE 4. Place the fuel valve lever in the ON position. Fig. U 5. Move the choke to the CLOSED Position. Fig. V 14

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
ENGLISH
14
15. Place the engine ON/OFF switch
 27 
in the ON position.
OFF
ON
Fig. Q
27
ENGINE
16. Press the ON/STOP button
 28 
for 2 seconds. The
green READY light will illuminate. The yellow WATER
FLOW light should also illuminate to verify the water is
connected properly and turned on.
Fig. R
28
17. When the green system ready light illuminates,
squeeze the spray gun trigger to start the engine.
After squeezing the spray gun trigger it will take
approximately 3 seconds for engine to start. After
the engine has started, the water flow will begin
and the yellow water flow light will illuminate. See
the
PRESSUREADY
® Fault Codes Table
in the
Troubleshooting
section
for more information.
NOTE:
The spray gun is equipped with a spring loaded
trigger lock 
 16 
. Manually release trigger lock as shown in
Fig. S.
Fig. S
16
±
WARNING:
Risk of unsafe operation. Stand on a
stable surface and grip spray gun/wand firmly with
both hands. Expect the spray gun/wand to kickback
when triggered.
18. When spray gun trigger is released, water flow will
stop immediately and the engine will shut off in
approximately 10 seconds. Ensure spring loaded trigger
lock is moved forward into the locked position.
19. To restart pressure washer, manually release trigger lock
and squeeze the spray gun trigger and the engine will
restart. Note that it will take approximately 3 seconds for
engine to start after squeezing spray gun trigger. After
the engine has started, the water flow will begin.
±
DANGER:
Risk of injury from spray. Ensure the spring
loaded trigger lock 
 16 
is moved forward to the locked
position, when the spray gun is not in use to prevent
accidental spraying.
Alternate Manual Mode
Start-up Procedure
(Without Battery)
(Fig. A, T–Z)
1. In a well-ventilated outdoor area, add fresh, high-quality,
unleaded gasoline with a pump octane rating of 86
or higher. Do not overfill. Wipe up spilled fuel before
starting the engine. Refer to engine instruction manual
for correct procedure.
IMPORTANT: Ethanol Shield™ (sold separately) is a fuel
stabilizer that helps eliminate and prevent ethanol
related problems in power equipment. Follow the
instructions on the container and add to the gasoline.
NOTICE:
Use of fuels with greater than 10% ethanol
are not approved for use in this product per EPA
regulations and will damage the unit and void
the warranty.
2. Check engine oil level. Refer to the engine instruction
manual for correct procedure.
NOTICE:
The engine is shipped without oil. Before
starting engine, add the oil provided. Damage to the
engine will occur if the engine is run without oil, this
damage will not be covered under warranty.
3. Place the engine ON/OFF switch
 27 
in the ON position.
OFF
ON
Fig. T
27
ENGINE
4. Place the fuel valve lever in the ON position.
Fig. U
5. Move the choke to the CLOSED Position.
Fig. V