Dewalt DXPW3400PR Instruction Manual - Page 19

STORAGE, Engine, Pressure Washer, ACCESSORIES, Service Information

Get Dewalt DXPW3400PR PDF manuals and user guides View all Dewalt DXPW3400PR manuals
Add to My Manuals
Save this manual to your list of manuals

Page 19 highlights

Fig. EE 14 STORAGE Engine Consult the engine instruction manual for the recommendations for storage. To Prevent Fuel-Related Problems 1. Add Ethanol Shield™ fuel stabilizer following the manufacturer's instructions. When adding a gasoline stabilizer, fill the fuel tank with fresh gasoline. If only partially filled, air in the tank will promote fuel deterioration during storage. If you keep a container of gasoline for refueling, be sure that it contains only fresh gasoline. 2. After adding a gasoline stabilizer: a. Connect the cold water source to pump inlet, turn on cold water source and squeeze the spray gun trigger for approximately 30 seconds or until a steady stream of water is present. Release the spray gun trigger. b. Start pressure washer/engine. See Starting for the correct procedure. Run the engine outdoors for 10 minutes to be sure that treated gasoline has replaced the untreated gasoline in the carburetor. 3. Turn the fuel valve to the OFF position. 4. Continue to run the engine until it stops from the lack of fuel in the carburetor fuel bowl. Running time should be less than 3 minutes. 5. Turn off the cold water source. Pump The manufacturer recommends using SIMPSON® / POWERWASHER™ Pump Guard or equivalent when storing the unit for more than 30 days and/or when freezing temperatures are expected. SIMPSON® / POWERWASHER™ Pump Guard is environmentally friendly. NOTE: Using pump guard helps provide proper lubrication to the internal seals of the pump regardless of temperature or environment. NOTICE: Risk of property damage. Use only SIMPSON® / POWERWASHER™ Pump Guard or equivalent. Other products could be corrosive and/or contain alcohol which may cause pump damage. 1. Turn off pressure washer and disconnect hoses from pump. 2. Unscrew bottle valve from Pump Guard bottle and remove seal. 3. Screw bottle valve back onto bottle. English 4. Attach bottle to water inlet of pump. 5. Squeeze bottle to inject contents into pump.  WARNING: Use Manual Mode Start-up Procedure (without battery) instructions. Do not install battery. 6. With the engine ON/OFF switch in the OFF position, simultaneously pull starter rope and squeeze bottle. Repeat until protector fluid exits pump outlet. NOTE: This step may require two people. Pressure Washer  WARNING: Risk of Damage. DO NOT store battery pack in pressure washer when not in use. Remove battery pack after every use. 1. Shut down the pressure washer. See Shutting Down for the correct procedure. 2. Drain all water from high pressure hose, coil it and store it in cradle of the pressure washer handle. 3. With nozzle pointed down and the spray gun and wand in a vertical position, squeeze spray gun trigger to drain all water from spray gun and wand. Store in spray gun holder. 4. Store chemical/soap hose so it is protected from damage. NOTICE: Risk of property damage. Always store and transport unit in an upright position. ACCESSORIES  WARNING: Since accessories, other than those offered by DeWALT, have not been tested with this product, use of such accessories with this pressure washer could be hazardous. To reduce the risk of injury, only DeWALT recommended accessories should be used with this product. Recommended accessories for use with your pressure washer are available for purchase from your local dealer or authorized service center. If you need assistance in locating any accessory for your pressure washer, please contact the FNA Group at [email protected], 7152 99th Street Pleasant Prairie, WI 53158, or call 1-877-362-4271.  DANGER: Risk of fluid injection. When using replacement lances or guns with this pressure washer, do not use a lance and/or lance/gun combination that is shorter in length than what was provided with this pressure washer as measured from the nozzle end of the lance to the gun trigger.  WARNING: The use of any other accessory not recommended for use with this pressure washer could be hazardous. Use only accessories rated equal to or higher than the rating of the pressure washer. Service Information Please have the following information available for all service calls: Model Number Serial Number Date and Place of Purchase 17

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
ENGLISH
17
Fig. EE
14
STORAGE
Engine
Consult the engine instruction manual for the
recommendations for storage.
To Prevent Fuel-Related Problems
1. Add Ethanol Shield™ fuel stabilizer following the
manufacturer’s instructions. When adding a gasoline
stabilizer, fill the fuel tank with fresh gasoline. If
only partially filled, air in the tank will promote fuel
deterioration during storage. If you keep a container
of gasoline for refueling, be sure that it contains only
fresh gasoline.
2. After adding a gasoline stabilizer:
a. Connect the cold water source to pump inlet, turn on
cold water source and squeeze the spray gun trigger
for approximately 30 seconds or until a steady stream
of water is present. Release the spray gun trigger.
b. Start pressure washer/engine. See
Starting
for the
correct procedure. Run the engine outdoors for 10
minutes to be sure that treated gasoline has replaced
the untreated gasoline in the carburetor.
3. Turn the fuel valve to the OFF position.
4. Continue to run the engine until it stops from the lack of
fuel in the carburetor fuel bowl. Running time should be
less than 3 minutes.
5. Turn off the cold water source.
Pump
The manufacturer recommends using SIMPSON® /
POWERWASHER™ Pump Guard or equivalent when storing
the unit for more than 30 days and/or when freezing
temperatures are expected. SIMPSON® / POWERWASHER™
Pump Guard is environmentally friendly.
NOTE:
Using pump guard helps provide proper lubrication
to the internal seals of the pump regardless of temperature
or environment.
NOTICE:
Risk of property damage. Use only
SIMPSON® / POWERWASHER™ Pump Guard or
equivalent. Other products could be corrosive and/or
contain alcohol which may cause pump damage.
1. Turn off pressure washer and disconnect hoses
from pump.
2. Unscrew bottle valve from Pump Guard bottle and
remove seal.
3. Screw bottle valve back onto bottle.
4. Attach bottle to water inlet of pump.
5. Squeeze bottle to inject contents into pump.
±
WARNING:
Use
Manual Mode Start-up
Procedure (without battery)
instructions.
Do not
install battery.
6. With the engine ON/OFF switch in the OFF position,
simultaneously pull starter rope and squeeze bottle.
Repeat until protector fluid exits pump outlet.
NOTE: 
This step may require two people.
Pressure Washer
±
WARNING:
Risk of Damage. DO NOT store battery
pack in pressure washer when not in use. Remove
battery pack after every use.
1. Shut down the pressure washer. See
Shutting Down
for
the correct procedure.
2. Drain all water from high pressure hose, coil it and store
it in cradle of the pressure washer handle.
3. With nozzle pointed down and the spray gun and wand
in a vertical position, squeeze spray gun trigger to
drain all water from spray gun and wand. Store in spray
gun holder.
4. Store chemical/soap hose so it is protected
from damage.
NOTICE:
Risk of property damage. Always store and
transport unit in an upright position.
ACCESSORIES
±
WARNING:
Since accessories, other than those
offered by
D
E
WALT
, have not been tested with this
product, use of such accessories with this pressure
washer could be hazardous. To reduce the risk of
injury, only
D
E
WALT
recommended accessories should
be used with this product.
Recommended accessories for use with your pressure
washer are available for purchase from your local dealer or
authorized service center. If you need assistance in locating
any accessory for your pressure washer, please contact the
FNA Group at [email protected], 7152 99th Street
Pleasant Prairie, WI 53158, or call 1–877–362–4271.
±
DANGER:
Risk of fluid injection. When using
replacement lances or guns with this pressure washer,
do not use a lance and/or lance/gun combination
that is shorter in length than what was provided with
this pressure washer as measured from the nozzle end
of the lance to the gun trigger.
±
WARNING:
The use of any other accessory not
recommended for use with this pressure washer could
be hazardous. Use only accessories rated equal to or
higher than the rating of the pressure washer.
Service Information
Please have the following information available for all
service calls: Model Number
___________________
Serial Number
_____________________________
Date and Place of Purchase ____________________