Dewalt DXPW3400PR Instruction Manual - Page 25

Quick Setup Guide, Quick Start Guide

Get Dewalt DXPW3400PR PDF manuals and user guides View all Dewalt DXPW3400PR manuals
Add to My Manuals
Save this manual to your list of manuals

Page 25 highlights

English QUICK SETUP GUIDE  WARNING: To reduce the risk of injury, read the pressure washer instruction manual and the engine instruction manual before operating pressure washer. A Install the Handle Slide the handle assembly onto the frame. Align holes, insert saddle bolts and secure in place with knobs. Tighten until snug. Align holes in the top handle with the mounting holes in the handle assembly. Insert saddle bolts through aligned holes and secure top handle to handle assembly with knobs. Tighten until snug. B Add/Check Oil The engine is shipped without oil. Before starting engine, add the oil provided. Check oil level prior to each use. Refer to Engine Owner's Manual for complete procedure. C Add Gasoline In a well ventilated outdoor area add fresh, high quality, unleaded gasoline with a pump octane rating of 86 or higher. Do not overfill. Wipe up spilled fuel before starting the engine. Refer to Engine Owners Manual for complete procedure. IMPORTANT: Ethanol Shield™ (sold separately) is a fuel stabilizer that helps eliminate and prevent ethanol related problems in power equipment. Follow the instructions on the container and add to the gasoline. QUICK START GUIDE  DANGER: • Never run engine indoors or in enclosed, poorly ventilated areas. Engine exhaust contains carbon monoxide, an odorless and deadly gas. • Risk of fluid injection and laceration. When using the high-pressure setting, DO NOT allow the high-pressure spray to come in contact with unprotected skin, eyes or with any pets or animals. Serious injury will occur.  WARNING: WHEN OPERATING IN MANUAL MODE ONLY: Do not allow the unit to run for more than two minutes without the spray gun trigger being pulled. This could cause overheating and damage to the pump. When the temperature inside the pump rises too high, the thermal relief valve will open and release a spray of water from the pump to lower the internal temperature. The valve will then close. 1 Place the Engine ON/ OFF switch in the OFF position 2 Connect Garden Hose to Pump Remove air and flush debris from garden hose before connecting to pump. Thread the garden hose to the pump inlet. 3 Connect High Pressure Hose to Pump Connect the high pressure hose to the pump outlet. 4 Connect High Pressure Hose to Spray Gun Connect the other end of the high pressure hose to the spray gun. ON OFF ENGINE 23

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
ENGLISH
23
QUICK SETUP GUIDE
±
WARNING:
To reduce the risk of injury, read the pressure washer instruction manual and the engine instruction manual
before operating pressure washer.
A
Install the Handle
Slide the handle assembly onto the frame. Align holes,
insert saddle bolts and secure in place with knobs. Tighten
until snug. Align holes in the top handle with the mounting
holes in the handle assembly. Insert saddle bolts through
aligned holes and secure top handle to handle assembly
with knobs. Tighten until snug.
B
Add/Check Oil
The engine is shipped without oil. Before starting engine,
add the oil provided. Check oil level prior to each use. Refer
to
Engine Owner’s Manual
for complete procedure.
C
Add Gasoline
In a well ventilated outdoor area add fresh, high quality,
unleaded gasoline with a pump octane rating of 86
or higher. Do not overfill. Wipe up spilled fuel before
starting the engine. Refer to
Engine Owners Manual
for
complete procedure.
IMPORTANT: Ethanol Shield
™
(sold separately) is a fuel stabilizer that helps eliminate and prevent ethanol related
problems in power equipment. Follow the instructions on the container and add to the gasoline.
QUICK START GUIDE
±
DANGER:
•
Never run engine indoors or in enclosed, poorly ventilated areas. Engine exhaust contains carbon monoxide, an
odorless and deadly gas.
•
Risk of fluid injection and laceration. When using the high-pressure setting, DO NOT allow the high-pressure spray to
come in contact with unprotected skin, eyes or with any pets or animals. Serious injury will occur.
±
WARNING:
WHEN OPERATING IN MANUAL MODE ONLY: Do not allow the unit to run for more than two
minutes without the spray gun trigger being pulled. This could cause overheating and damage to the pump.
When the temperature inside the pump rises too high, the thermal relief valve will open and release a spray
of water from the pump to lower the internal temperature. The valve will then close.
1
Place the Engine ON/
OFF switch in the OFF
position
2
Connect Garden Hose
to Pump
Remove air and flush debris
from garden hose before
connecting to pump.
Thread the garden hose to
the pump inlet.
3
Connect High
Pressure Hose to
Pump
Connect the high pressure
hose to the pump outlet.
4
Connect High
Pressure Hose to
Spray Gun
Connect the other end of the
high pressure hose to the
spray gun.
OFF
ON
ENGINE