Epson ActionTower 3000 User Manual - Page 91

Post-installation Procedures, next for post-installation instructions.

Get Epson ActionTower 3000 PDF manuals and user guides View all Epson ActionTower 3000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 91 highlights

5. Replace the bracket inside the computer as shown below and secure it to the back panel with the four screws you removed 6. If there is another drive installed in the rear internal drive bay, follow the instructions starting on page 4-17 to reconnect the drive and power cables to the drive. 7. When you are finished installing or removing drives, replace the computer's cover (described in Chapter 3) and see the next section for post-installation instructions. Post-installation Procedures After you install or remove your drive(s) and replace the cover on your computer, you need to run SETUP to define your new drive configuration. See Chapter 1 for instructions. Installing and Removing Drives 4-21

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
5. Replace the bracket inside the computer as shown below and
secure it to the back panel with the four screws you removed
6.
If there is another drive installed in the rear internal drive
bay, follow the instructions starting on page 4-17 to
reconnect the drive and power cables to the drive.
7.
When you are finished installing or removing drives, replace
the computer’s cover (described in Chapter 3) and see the
next section for post-installation instructions.
Post-installation Procedures
After you install or remove your drive(s) and replace the cover
on your computer, you need to run SETUP to define your new
drive configuration. See Chapter 1 for instructions.
Installing and Removing Drives
4-21