Epson PowerLite 4300 User's Guide - Page 90

Solving Problems With the Image

Get Epson PowerLite 4300 PDF manuals and user guides View all Epson PowerLite 4300 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 90 highlights

Solving Problems With the Image No image appears on the screen. ■ Check that the Ppower light is green, not flashing, and that the lens cover is removed. ■ The projector may be in standby or sleep mode. If the Ppower light is orange, press the Ppower button to turn the projector on. ■ If the power was switched off and then on again, the projector may be cooling down. Wait until the Ppower light stops flashing and remains orange; then press the Ppower button again. ■ Press the A/V Mute button on the remote control to make sure the picture has not been turned off temporarily. ■ The attached computer may be in sleep mode or displaying a black screen saver. Try pressing a key on the computer. ■ If you are projecting from a DVD player or other video source, make sure you turn it on and press its Play button. ■ If you are projecting from a video source, make sure the Video Signal setting is correct (see page 58). ■ You can also try resetting all of the configuration menu settings. See page 55. You've connected a computer and see a blue screen with the message No Signal displayed. ■ Make sure the cables are connected correctly, as described beginning on page 16. ■ If you've connected more than one computer and/or video source, you may need to press the Source Search button on the projector's control panel, or the Search button or one of the Source buttons on the remote control to select the correct source. (Allow a few seconds for the projector to sync up after pressing the button.) ■ Make sure the power for your connected equipment is turned on. 90 Solving Problems

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
90
Solving Problems
Solving Problems With the Image
No image appears on the screen.
■
Check that the
P
power light is green, not flashing, and that the
lens cover is removed.
■
The projector may be in standby or sleep mode. If the
P
power
light is orange, press the
P
power button to turn the projector on.
■
If the power was switched off and then on again, the projector
may be cooling down. Wait until the
P
power light stops flashing
and remains orange; then press the
P
power button again.
■
Press the
A/V Mute
button on the remote control to make sure
the picture has not been turned off temporarily.
■
The attached computer may be in sleep mode or displaying a
black screen saver. Try pressing a key on the computer.
■
If you are projecting from a DVD player or other video source,
make sure you turn it on and press its
Play
button.
■
If you are projecting from a video source, make sure the Video
Signal setting is correct (see page 58).
■
You can also try resetting all of the configuration menu settings.
See page 55.
You’ve connected a computer and see a blue screen with the
message
No Signal
displayed.
■
Make sure the cables are connected correctly, as described
beginning on page 16.
■
If you’ve connected more than one computer and/or video source,
you may need to press the
Source Search
button on the
projector’s control panel, or the
Search
button or one of the
Source
buttons on the remote control to select the correct source.
(Allow a few seconds for the projector to sync up after pressing the
button.)
■
Make sure the power for your connected equipment is turned on.