Epson PowerLite 50c User Manual - Page 36

Using the Remote Control, Installing the Remote Control Batteries - replacement remote

Get Epson PowerLite 50c PDF manuals and user guides View all Epson PowerLite 50c manuals
Add to My Manuals
Save this manual to your list of manuals

Page 36 highlights

Using the Remote Control The remote control lets you access projector features from anywhere in the room-up to 32 feet away. You must also be within a 30° horizontal and a 15° vertical angle of the infrared receiver on the front of the projector. You can use the remote control to turn the projector on and off, zoom the image, display the projector menus, and other uses.If you connected a mouse cable to the projector, you can also use the remote control as a wireless mouse to run your presentation. See page 32 for instructions. Installing the Remote Control Batteries The remote control operates the projector and lets you access its setup menus. You can also use it as a wireless mouse. Follow these steps to install the batteries: 1. Press the tab to release the battery cover and lift it up to remove it. 2. Insert the two AA batteries included with the projector as shown. 3. Replace the battery cover. infrared receiver for remote control note You can aim the remote control at your projection screen and reflect the signal back into the sensor on the front of the projector, but this shortens the operating distance of the remote control. caution When replacing batteries, take the following precautions: s Replace batteries as soon as they run out. s Do not mix old and new batteries. s If the batteries leak, wipe away battery fluid with a soft cloth. If fluid gets on your hands, wash them immediately. s Remove batteries if you will not be using the remote for a long period of time. Using the Projector 31

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
Using the Projector
31
Using the Remote Control
The remote control lets you access projector features from anywhere
in the room
—
up to 32 feet away. You must also be within a 30
°
horizontal and a 15
°
vertical angle of the infrared receiver on the front
of the projector.
You can use the remote control to turn the projector on and off, zoom
the image, display the projector menus, and other uses.If you
connected a mouse cable to the projector, you can also use the remote
control as a wireless mouse to run your presentation. See page 32 for
instructions.
Installing the Remote Control Batteries
The remote control operates the projector and lets you access its setup
menus. You can also use it as a wireless mouse.
Follow these steps to install the
batteries:
1.
Press the tab to release the battery
cover and lift it up to remove it.
2.
Insert the two AA batteries
included with the projector
as shown.
3.
Replace the battery cover.
infrared receiver
for remote control
note
You can aim the remote
control at your projection
screen and reflect the signal
back into the sensor on the
front of the projector, but this
shortens the operating
distance of the remote
control.
caution
When replacing batteries,
take the following
precautions:
■
Replace batteries as soon
as they run out.
■
Do not mix old and new
batteries.
■
If the batteries leak, wipe
away battery fluid with a
soft cloth. If fluid gets on
your hands, wash them
immediately.
■
Remove batteries if you
will not be using the
remote for a long period
of time.