Epson PowerLite Pro Cinema 6010 User's Guide - Page 65

Solving Picture Problems

Get Epson PowerLite Pro Cinema 6010 PDF manuals and user guides View all Epson PowerLite Pro Cinema 6010 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 65 highlights

Lights indicating a problem Light state The temperature light flashes red Cause and solution There is a fan or sensor problem. Turn off the projector and unplug it from the electrical outlet. Then contact Epson for assistance (see page 70). Both warning lights are flashing red There is an internal problem. Turn off the projector and unplug it from the electrical outlet. Then contact Epson for assistance (see page 70). Solving Picture Problems You cannot turn on the projector. ■ Make sure the power cord is connected and the power switch on the back of the projector is turned on. Then wait a moment for the Ppower button to light up before pressing the Ppower button on the projector or the On button on the remote control. ■ If you've set the Control Panel Lock, the control panel buttons are disabled; you must use the remote control to turn on the projector (see page 32). ■ If you've set the Child Lock, you have to press the Ppower button on the projector for 3 seconds to turn on the projector, or use the remote control (see page 32). No picture appears on the screen or you see the No Signal message displayed. ■ Press one of the Source buttons on the remote control, or press the source button on the projector, to select the correct input source. Allow a few seconds for the projector to sync up after pressing the button. ■ Press the Blank button on the remote control to make sure the picture hasn't been turned off temporarily. ■ Check that the power light is on and not flashing, and the lens cover is open. ■ The projector may be in standby (or sleep) mode. If the Ppower button is lit and the power light is off, press the Ppower button to turn the projector back on. ■ Make sure your video equipment is turned on. ■ Make sure your cable(s) are connected correctly (see page 17). Problem Solving 65

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
Problem Solving
65
Solving Picture Problems
You cannot turn on the projector.
■
Make sure the power cord is connected and the power switch on the back of the projector
is turned on. Then wait a moment for the
P
power button to light up before pressing the
P
power button on the projector or the
On
button on the remote control.
■
If you’ve set the
Control Panel Lock
, the control panel buttons are disabled; you must
use the remote control to turn on the projector (see page 32).
■
If you’ve set the
Child Lock
, you have to press the
P
power button on the projector for 3
seconds to turn on the projector, or use the remote control (see page 32).
No picture appears on the screen or you see the
No Signal
message
displayed.
■
Press one of the
Source
buttons on the remote control, or press the
source button
on the projector, to select the correct input source. Allow a few seconds for the projector
to sync up after pressing the button.
■
Press the
Blank
button on the remote control to make sure the picture hasn’t been turned
off temporarily.
■
Check that the power light is on and not flashing, and the lens cover is open.
■
The projector may be in standby (or sleep) mode. If the
P
power button is lit and the
power light is off, press the
P
power button to turn the projector back on.
■
Make sure your video equipment is turned on.
■
Make sure your cable(s) are connected correctly (see page 17).
The temperature
light flashes red
There is a fan or sensor problem. Turn off the projector and
unplug it from the electrical outlet. Then contact Epson for
assistance (see page 70).
Both warning
lights are
flashing red
There is an internal problem.
Turn off the projector and unplug it
from the electrical outlet. Then contact Epson for assistance (see
page 70).
Lights indicating a problem
Light state
Cause and solution