Home » HP Manuals » Laser Printers » HP 2300d » Manual Viewer

HP 2300d HP LaserJet 2300 printer - User Guide - Page 160

Idle Timeout, Source Routing

UPC - 808736471091

Add to My Manuals
Save this manual to your list of manuals

Page 160 highlights

Item DHCP settings Manual settings IPX/SPX ENABLE FRAME TYPE SOURCE ROUTING APPLETALK ENABLE DLC/LLC ENABLE Values Explanation DHCP RELEASE *NO YES This menu appears if CONFIG METHOD is set to DHCP and a DHCP lease for the print server exists. NO (default): The current DHCP lease is saved. YES: The current DHCP lease along with the leased IP address are released. DHCP RENEW *NO YES This menu appears if CONFIG METHOD is set to DHCP and a DHCP lease for the print server exists. NO (default): The print server does not request to renew the DHCP lease. YES: The print server requests to renew the current DHCP lease. IP ADDRESS n.n.n.n The unique IP address of the printer, where n is a value from 0 to 255. SUBNET MASK m.m.m.m The subnet mask for the printer, where m is a value from 0 to 255. The mask is applied to IP addresses to uniquely identify subnetworks and nodes. SYSLOG SERVER n.n.n.n The IP address of the syslog server used to receive and log syslog messages. DEFAULT GATEWAY n.n.n.n The IP address of the gateway or route used for communications with other networks. IDLE TIMEOUT XX The timeout value (in seconds) before an idle TCP print data connection is automatically closed. The default value is 270 seconds. 0 disables the timeout. There is no value to select. OFF Select whether the IPX/SPX protocol stack (in Novell *ON NetWare networks, for example) is enabled or disabled. *AUTO EN_8023 EN_II EN_SNAP TR_8022 TR_SNAP Select the frame type setting for your network. AUTO (default): Automatically sets and limits the frame type to the first one detected. For an Ethernet network only, frame type selections include EN_8023, EN_II, EN_8022, and EN_SNAP. For a Token Ring network only, frame type selections include TR_8022 and TR_SNAP. *AUTO OFF ALL ROUTES SINGLE ROUTE For a Token Ring network only, specify the NetWare Token Ring Source Routing parameter. AUTO (default): The type of source routing required on the network is automatically sensed. OFF: All packets are sent without source routing, and only packets from the same ring are received. ALL ROUTES and SINGLE ROUTE: All packets are sent with source routing (broadcasts and when the route is unknown). There is no value to select. OFF For an Ethernet network only, select whether the AppleTalk *ON protocol stack is enabled or disabled. There is no value to select. OFF Select whether the DLC/LLC protocol stack is enabled or *ON disabled. 158 B Control panel menus ENWW

Section	Page
Printer basics	9
Printer configurations	10
Printer features	11
Printer software	13
Operating systems and printer components	14
Printer drivers	16
Software for Macintosh computers	17
Installing the printing system software	18
Installing Windows printing system software for direct connections	18
Installing Windows printing system software for networks	19
Installing Macintosh printing system software for networks	20
Installing Macintosh printing system software for direct connections	21
Installing the software after the parallel or USB cable has been connected	22
Uninstalling the software	23
Control panel	24
Control panel layout	24
Using the printer Help system	27
Printing control panel menus	27
Changing control panel settings	27
Interface ports	28
Printing tasks	29
Purchasing paper and other media	30
Media input options	31
Tray1 media sizes	31
Tray2 (250sheet tray) paper sizes	32
Tray3 (500sheettray) paper sizes	32
Loading trays	33
Loading tray1 (multipurpose tray)	33
Loading tray2 (250sheettray) or optional 250sheettray in tray3 position	34
Loading tray3 (500sheettray)	36
Media output options	37
Printing on special media	38
Printing on envelopes	39
Printing on labels	41
Printing on transparencies	42
Printing on customsized media or cardstock	43
Printing on letterhead, prepunched, or preprinted paper (singlesided)	44
Printing on both sides (duplexing)	45
Canceling a print job	48
Using the printer driver	49
Changing the settings for a print job	49
Changing default settings	50
Using printerdriver features	51
Printing watermarks	51
Printing multiple pages on one sheet of paper	52
Setting a custom paper size	52
Using EconoMode (draft) printing	53
Choosing printquality settings	53
Using reduce/enlarge options	54
Selecting a paper source	54
Printing by type and size of media	55
Printing a cover or different first page	56
Adding a blank page or back cover to the end of a print job	57
Adding a blank page to the beginning of all print jobs (job separator page)	57
Using job-storage features	59
Proofing and holding a job	59
Deleting a held job	60
Printing a private job	60
Deleting a private job	61
Managing and maintaining the printer	63
Using the embeddedWebserver	64
Opening the embedded Web server	64
Information tab	65
Settings tab	65
Networking tab	65
Other links	66
Using HPWebJetadmin software	66
Using Printer Status and Alerts	67
Managing and configuring printer drivers	68
HP Web Jetadmin software plugin	68
Customization utility	69
Managing the print cartridge	70
HPprint cartridges	70
NonHP print cartridges	70
Printcartridge authentication	70
Printcartridge storage	70
Printcartridge life expectancy	71
Checking the supply level	71
Cartridge low and cartridge out conditions	72
Configuring email alerts	73
Checking the printer configuration	74
Menu map	74
Configuration page	74
Supplies status page	76
PS or PCL font list	78
Cleaning the printer	79
Cleaning the outside	79
Cleaning the paper path and printcartridge areas	80
Cleaning the fuser	81
Problem solving	83
Troubleshooting checklist	84
Troubleshooting general printing problems	85
Printing special pages	89
Understanding printer messages	90
Using the printer online Help system	90
Resolving persistent messages	90
Interpreting controlpanel messages	91
Clearing jams	99
Typical jam locations	99
Printcartridge area	100
Tray2 or tray3 paperfeed area	101
Output areas	102
Duplexer area	103
Troubleshooting printquality problems	104
Printquality checklist	104
Image defect examples	105
Troubleshooting network printing problems	109
Troubleshooting common Windows problems	110
Troubleshooting common Macintosh problems	111
Troubleshooting common PostScript problems	116
Service and support	117
Ordering parts, accessories, and supplies	118
Ordering directly from HP	118
Ordering through service or support providers	118
Ordering directly through the embeddedWebserver (for printers with network connection)	118
Ordering directly through the printer software (for printers directly connected to a computer)	119
Part numbers	120
Contacting HP	125
Getting support	125
Obtaining extended service and support	126
Contacting the HPfraud hotline	126
Guidelines for repacking the printer	127
Service information form	128
HP maintenance agreements	129
Warranty information	130
HewlettPackard limited warranty statement	131
Extended warranty	132
Limited warranty for print cartridge life	132
Specifications	133
Printer specifications	134
Physical specifications	134
Electrical specifications	134
Power consumption	134
Acoustic emissions	135
Operating environment	135
Media specifications	136
Supported sizes of media	136
Guidelines for using paper	138
Paper specifications	139
Printing and paper storage environment	140
Envelopes	141
Labels	143
Transparencies	143
Control panel menus	145
Retrieve Job menu	146
Information menu	147
Paper Handling menu	148
Configure Device menu	150
Printing submenu	150
PCL submenu	152
Print Quality submenu	153
System Setup submenu	156
I/O submenu	159
Resets submenu	162
Diagnostics menu	163
Service menu	163
Printer memory and expansion	165
Printer memory	166
Installing memory	167
Checking memory installation	169
Installing an HPJetdirect EIO card	170
Printer commands	171
Understanding PCL printer command syntax	172
Combining escape sequences	172
Entering escape characters	173
Selecting PCL 5e fonts	173
Common PCL 5e printer commands	174
Regulatory information	177
FCC regulations	177
Environmental product stewardship program	178
Declarations of conformity	180
Declaration of Conformity	180
Canadian DOC regulations	181
Regulatory and safety statements	182
Laser safety statement	182
LED safety statement	182
Japanese VCCI statement	182
Korean EMI statement	182
Laser statement for Finland	183
Index	185
Symbols	185
Numerics	185
A	185
B	185
C	185
D	186
E	187
F	187
G	187
H	187
I	188
J	188
K	188
L	188
M	189
N	189
O	189
P	190
Q	191
R	191
S	191
T	192
U	193
V	193
W	193

Match case Limit results 1 per page

158

B Control panel menus

ENWW

DHCP

settings

DHCP RELEASE

*NO

YES

This menu appears if

CONFIG METHOD

is set to

DHCP

and a

DHCP lease for the print server exists.

(default): The current DHCP lease is saved.

YES

: The current DHCP lease along with the leased IP

address are released.

DHCP RENEW

*NO

YES

This menu appears if CONFIG METHOD is set to

DHCP

and

a DHCP lease for the print server exists.

(default): The print server does not request to renew the

DHCP lease.

YES

: The print server requests to renew the current DHCP

lease.

Manual settings

IP ADDRESS

n.n.n.n

The unique IP address of the printer, where

is a value

from 0 to 255.

SUBNET MASK

m.m.m.m

The subnet mask for the printer, where

is a value from 0

to 255. The mask is applied to IP addresses to uniquely

identify subnetworks and nodes.

SYSLOG SERVER

n.n.n.n

The IP address of the syslog server used to receive and log

syslog messages.

DEFAULT

GATEWAY

n.n.n.n

The IP address of the gateway or route used for

communications with other networks.

IDLE TIMEOUT

The timeout value (in seconds) before an idle TCP print

data connection is automatically closed. The default value

is 270 seconds. 0 disables the timeout.

IPX/SPX

There is no value to select.

ENABLE

OFF

Select whether the IPX/SPX protocol stack (in Novell

NetWare networks, for example) is enabled or disabled.

FRAME TYPE

*AUTO

EN_8023

EN_II

EN_SNAP

TR_8022

TR_SNAP

Select the frame type setting for your network.

AUTO

(default): Automatically sets and limits the frame type

to the first one detected.

For an Ethernet network only, frame type selections include

EN_8023

EN_II

EN_8022

, and

EN_SNAP

For a Token Ring network only, frame type selections

include

TR_8022

and

TR_SNAP

SOURCE ROUTING

*AUTO

OFF

ALL ROUTES

SINGLE ROUTE

For a Token Ring network only, specify the NetWare Token

Ring Source Routing parameter.

AUTO

(default): The type of source routing required on the

network is automatically sensed.

OFF

: All packets are sent without source routing, and only

packets from the same ring are received.

ALL ROUTES

and

SINGLE ROUTE

: All packets are sent with

source routing (broadcasts and when the route is

unknown).

APPLETALK

There is no value to select.

ENABLE

OFF

For an Ethernet network only, select whether the AppleTalk

protocol stack is enabled or disabled.

DLC/LLC

There is no value to select.

ENABLE

OFF

Select whether the DLC/LLC protocol stack is enabled or

disabled.

Item

Values

Explanation