HP 2300d HP LaserJet 2300 printer - User Guide - Page 168

Repeat steps 6

Get HP 2300d - LaserJet B/W Laser Printer PDF manuals and user guides
UPC - 808736471091
View all HP 2300d manuals
Add to My Manuals
Save this manual to your list of manuals

Page 168 highlights

6 6 Remove the DIMM from the antistatic package. CAUTION To reduce the possibility of damage caused by static electricity, always wear an electrostatic discharge (ESD) wrist strap or touch the surface of the antistatic package before handling DIMMs. 7 Holding the DIMM by the edges (as shown in the illustration), align 7 the notches on the DIMM with the DIMM slot. (Check that the locks on each side of the DIMM slot are open.) 8 Press the DIMM straight into the slot (press firmly). Make sure the locks on each side of the DIMM snap inward into place. (To remove a DIMM, the locks must be released.) Repeat steps 6, 7, and 8 for each DIMM being installed. 9 Reconnect the interface cable(s) and power cord. 10 To replace the side panel, line up the alignment arrows and slide 8 the panel backwards until the release button latches into place. 11 Close the top cover and turn the printer on. 9 10 166 Appendix C Printer memory and expansion ENWW

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
166
Appendix C Printer memory and expansion
ENWW
6
Remove the DIMM from the antistatic package.
CAUTION
To reduce the possibility of damage caused by static electricity, always
wear an electrostatic discharge (ESD) wrist strap or touch the surface of
the antistatic package before handling DIMMs.
7
Holding the DIMM by the edges (as shown in the illustration), align
the notches on the DIMM with the DIMM slot. (Check that the locks
on each side of the DIMM slot are open.)
8
Press the DIMM straight into the slot (press firmly). Make sure the
locks on each side of the DIMM snap inward into place. (To remove
a DIMM, the locks must be released.)
Repeat steps 6, 7, and 8 for each DIMM being installed.
9
Reconnect the interface cable(s) and power cord.
10
To replace the side panel, line up the alignment arrows and slide
the panel backwards until the release button latches into place.
11
Close the top cover and turn the printer on.
7
8
6
9
10