HP DesignJet Z6 User Guide - Page 35

CAUTION, WARNING, If the new roll core has a three-inch internal diameter

Get HP DesignJet Z6 PDF manuals and user guides View all HP DesignJet Z6 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 35 highlights

2. Remove the black end of the spindle from the printer, then the blue end. CAUTION: Be sure to remove the black end first. Removing the blue end first could damage the black end. WARNING! Do not insert your fingers into the spindle supports during the removal process. 3. The spindle has a stop at each end to keep the roll in position. The blue stop can be removed to mount a new roll; it slides along the spindle to hold rolls of different widths. Remove the blue paper stop from the end of the spindle. NOTE: If the new roll core has a three-inch internal diameter, ensure that the core adapters have been installed. See Order other accessories on page 145. 4. If the roll is long; rest the spindle horizontally on a table and load the roll on the table. TIP: You may need two people to handle a large roll. ENWW Load a roll onto the spindle 27

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
2.
Remove the black end of the spindle from the printer, then the blue end.
CAUTION:
Be sure to remove the black end
first.
Removing the blue end
first
could damage the black end.
WARNING!
Do not insert your
fingers
into the spindle supports during the removal process.
3.
The spindle has a stop at each end to keep the roll in position. The blue stop can be removed to mount a
new roll; it slides along the spindle to hold rolls of
different
widths. Remove the blue paper stop from the
end of the spindle.
NOTE:
If the new roll core has a three-inch internal diameter, ensure that the core adapters have been
installed. See
Order other accessories
on page
145
.
4.
If the roll is long; rest the spindle horizontally on a table and load the roll on the table.
TIP:
You may need two people to handle a large roll.
ENWW
Load a roll onto the spindle
27