HP Disk System 2300 HP StorageWorks Disk System 2300 User's Guide(This manual - Page 61

Place the storage device on the rails and slide it into the cabinet until

Get HP Disk System 2300 PDF manuals and user guides View all HP Disk System 2300 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 61 highlights

7. Install clipnuts on the front columns of the cabinet (see Figure 30). These are used for the device retention screws. Installation 8. Place the storage device on the rails and slide it into the cabinet until the retention bracket comes in contact with the rack column (see Figure 31). WARNING An empty storage device weighs approximately 54 pounds (without disk modules installed) (24.5 kg). To avoid personal injury, it is recommended that two people install the storage device in the rack. Installation 61

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
Installation
61
Installation
7.
Install clipnuts on the front columns of the cabinet (see
Figure 30
).
These are used for the device retention screws.
8.
Place the storage device on the rails and slide it into the cabinet until
the retention bracket comes in contact with the rack column (see
Figure 31
).
WARNING
An empty storage device weighs approximately 54 pounds
(without disk modules installed) (24.5 kg). To avoid personal
injury, it is recommended that two people install the storage device
in the rack.