HP Disk System 2300 HP StorageWorks Disk System 2300 User's Guide(This manual - Page 80

Step 8: Turn on the Disk System, Watch the system LEDs for confirmation that the disk system is

Get HP Disk System 2300 PDF manuals and user guides View all HP Disk System 2300 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 80 highlights

Step 8: Turn on the Disk System Caution When starting up the disk system, do not override automatic spinup by issuing SCSI start commands to the drives. Doing so could cause an overcurrent fault, requiring a power cycle to recover. Press in the power/standby switch with the retracted tip of a pen or pencil to power-on the array (see Figure 47). Allow 2 minutes for the disk drives and controllers to complete their self-tests. 1. Press the power switch (A in Figure 47) to turn on the disk system. 2. Watch the system LEDs for confirmation that the disk system is operational. The system power LED (B) should be green, and the fault LED (C) should be off. If the LEDs indicate a problem, refer to Chapter 4, Troubleshooting. Note An amber light that is on briefly when a component turns on is normal. If this light remains on more than a couple of seconds, a fault has been detected. 80 Installation

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
80
Installation
Step 8: Turn on the Disk System
Caution
When starting up the disk system, do not override automatic spin-
up by issuing SCSI start commands to the drives. Doing so could
cause an overcurrent fault, requiring a power cycle to recover.
Press in the power/standby switch with the retracted tip of a pen or pencil to
power-on the array (see
Figure 47
). Allow 2 minutes for the disk drives and
controllers to complete their self-tests.
1.
Press the power switch (A in
Figure 47
) to turn on the disk system.
2.
Watch the system LEDs for confirmation that the disk system is
operational. The system power LED (B) should be green, and the fault
LED (C) should be off.
If the LEDs indicate a problem, refer to Chapter 4, Troubleshooting.
Note
An amber light that is on briefly when a component turns on is
normal. If this light remains on more than a couple of seconds, a
fault has been detected.