HP Disk System 2300 HP StorageWorks Disk System 2300 User's Guide(This manual - Page 89

Disk Slots and Addressing, shown

Get HP Disk System 2300 PDF manuals and user guides View all HP Disk System 2300 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 89 highlights

Note In split bus mode, the enclosure monitor circuitry on each BCC utilizes SCSI address 15. This is allowable since each BCC is connected to a separate SCSI bus. However, when the enclosure configuration is in Full Bus mode, and the separate SCSI busses on the midplane are connected together and there are two BCCs in the enclosure, the secondary BCC does not connect to the SCSI bus. Disk Slots and Addressing The disk system has 14 available disk slots, SCSI addressing does not follow a "1-to-1" relationship between slot positions and SCSI addresses. Slot assignments and SCSI addresses are shown in Figure 49. Configuration In full bus mode, the SCSI address 7 is reserved for the host bus adapter. If more than one host bus adapter connects the disk system to other hosts, then a disk module must be removed from the slot whose SCSI address corresponds to the SCSI address of the additional host bus adapter. The most host bus adapters supported on this disk system is two. In split bus mode, the loading sequence is from slot 1 to the right to slot 7 and from slot 8 to the right to slot 14. In full bus mode, begin loading the disk modules in slot 1 and continue installing disk modules toward the right. Configuration 89

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
Configuration
89
Configuration
Note
In split bus mode, the enclosure monitor circuitry on each BCC
utilizes SCSI address 15. This is allowable since each BCC is
connected to a separate SCSI bus. However, when the enclosure
configuration is in Full Bus mode, and the separate SCSI busses on
the midplane are connected together and there are two BCCs in the
enclosure, the secondary BCC does not connect to the SCSI bus.
Disk Slots and Addressing
The disk system has 14 available disk slots, SCSI addressing
does not follow a “1-to-1” relationship between slot positions
and SCSI addresses. Slot assignments and SCSI addresses are
shown in Figure 49.
In full bus mode, the SCSI address 7 is reserved for the host bus adapter. If more
than one host bus adapter connects the disk system to other hosts, then a disk
module must be removed from the slot whose SCSI address corresponds to the
SCSI address of the additional host bus adapter. The most host bus adapters
supported on this disk system is two.
In split bus mode, the loading sequence is from slot 1 to the right to slot 7 and
from slot 8 to the right to slot 14.
In full bus mode, begin loading the disk modules in slot 1 and continue installing
disk modules toward the right.