HP Disk System 2300 HP StorageWorks Disk System 2300 User's Guide(This manual - Page 70

Install the Disk System, onto the rails

Get HP Disk System 2300 PDF manuals and user guides View all HP Disk System 2300 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 70 highlights

Install the Disk System 1. Remove the power supply/fan modules to prepare the disk system for lifting: a Loosen the screws in each extractor handle of each power supply/fan module with the chassis still in the box. b Pull the extractor handles out from the center of the power supply to disengage the it from the midplane. Pull each power supply/fan module out of the chassis. Support the far end of the power supply/fan module with your free hand as it clears the chassis. c Set the power supply/fan module aside, on an antistatic pad, to be reinstalled later. WARNING Do not attempt to lift the disk system without the help of another person or a lift device. Even without power supplies and disk drives, the disk system weighs 54 pounds. 2. Remove the disk modules from the disk system. Place them aside on the pink anti-static foam pad supplied with your disk system. 3. Carry the disk system to the front of the rack and slide the back end onto the rails (Figure 38) with the help of another person or using a lifting device. Push the disk system into the rack as far as it will go. 4. Secure the disk system as appropriate for the rail kit and cabinet at the installation site. 70 Installation

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
70
Installation
Install the Disk System
1.
Remove the power supply/fan modules to prepare the disk system for lifting:
a
Loosen the screws in each extractor handle of each power supply/fan
module with the chassis still in the box.
b
Pull the extractor handles out from the center of the power supply to
disengage the it from the midplane. Pull each power supply/fan module
out of the chassis. Support the far end of the power supply/fan module
with your free hand as it clears the chassis.
c
Set the power supply/fan module aside, on an antistatic pad, to be
reinstalled later.
WARNING
Do not attempt to lift the disk system without the help of another
person or a lift device. Even without power supplies and disk
drives, the disk system weighs 54 pounds.
2.
Remove the disk modules from the disk system. Place them aside on
the pink anti-static foam pad supplied with your disk system.
3.
Carry the disk system to the front of the rack and slide the back end
onto the rails (
Figure 38
) with the help of another person or using a
lifting device. Push the disk system into the rack as far as it will go.
4.
Secure the disk system as appropriate for the rail kit and cabinet at the
installation site.