HP LH4r HP NetServer FCArray Assistant - Installation and User Guide - Page 64

Power Levels

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 64 highlights

Chapter 4 NOTE Configuration If the Battery Backup Unit is not installed or connected on the FCArray Controller card, an error message will appear instead of the dialog box shown in Figure 4-26. If this is for the initial installation of the Rack Storage/12FC, the first time the FCArray Controller card is used, or a new BBU (battery pack) has been installed, the battery pack must be reconditioned before using the FCArray Controller card. The Reconditioning Battery process may take up to 15 hours to complete. Figure 4-26. Intelligent BBU Dialog Box The dialog box is divided into three groups, which are described in the items listed under the following sections: Power Levels Low Power Threshold - This indicates a preset power level, expressed as hours or minutes of charge, and is used to trigger an alarm. An alarm is triggered, when the battery pack's Current Power value drops below the setting in this field. This field is edited to change the existing value and then verified and applied to accept the change. Refer to Set Low Power Threshold under the Actions bullet for more information. 58

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
Chapter 4
Configuration
58
NOTE
If the Battery Backup Unit is not installed or connected on the
FCArray Controller card, an error message will appear instead
of the dialog box shown in Figure 4-26.
If this is for the initial installation of the Rack Storage/12FC,
the first time the FCArray Controller card is used, or a new
BBU (battery pack) has been installed, the battery pack must
be reconditioned before using the FCArray Controller card.
The Reconditioning Battery process may take up to 15 hours to
complete.
Figure 4-26. Intelligent BBU Dialog Box
The dialog box is divided into three groups, which are described in the items listed
under the following sections:
Power Levels
Low Power Threshold
- This indicates a preset power level, expressed
as hours or minutes of charge, and is used to trigger an alarm. An alarm
is triggered, when the battery pack’s Current Power value drops below
the setting in this field. This field is edited to change the existing value
and then verified and applied to accept the change. Refer to Set Low
Power Threshold under the Actions bullet for more information.