HP LH4r HP NetServer FCArray Assistant - Installation and User Guide - Page 89

Clear All, Set Sequential, Restore, Apply

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 89 highlights

Chapter 4 Configuration Figure 4-45. LUN Mapping in Simplex Mode Consider the following points. ◊ The Clear All button sets all LUN assignments to None. You can then select individual assignments more closely while allowing several assignments of "inaccessible." WARNING DO NOT leave all assignments at None. This indicates there are no logical drives accessible to any port on any controller. ◊ The Set Sequential button sets all LUN assignments sequentially on all available ports. This reproduces the default shown in Figure 4-45. ◊ The Restore button resets the LUN Mapping assignments currently saved in the configuration (the assignments in effect when the LUN Mapping page was entered). This is handy if LUN assignments become confusing and you wish to cancel your changes. ◊ The Apply button applies the entire RAID Controller configuration, including what was set up under the Disk Arrays, Logical Drives, and LUN Mapping tabs. 83

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
Chapter 4
Configuration
83
Figure 4-45. LUN Mapping in Simplex Mode
Consider the following points.
◊
The
Clear All
button sets all LUN assignments to None.
You can then select individual assignments more closely while
allowing several assignments of "inaccessible."
WARNING
DO NOT leave all assignments at None. This indicates there
are no logical drives accessible to any port on any controller.
◊
The
Set Sequential
button sets all LUN assignments sequentially on all
available ports. This reproduces the default shown in Figure 4-45.
◊
The
Restore
button resets the LUN Mapping assignments currently
saved in the configuration (the assignments in effect when the LUN
Mapping page was entered).
This is handy if LUN assignments become confusing and you wish to
cancel your changes.
◊
The
Apply
button applies the entire RAID Controller configuration,
including what was set up under the Disk Arrays, Logical Drives, and
LUN Mapping tabs.