HP LH4r HP NetServer FCArray Assistant - Installation and User Guide - Page 84

Supported RAID levels are RAID 0, RAID 1, RAID 3, RAID 5, RAID

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 84 highlights

Chapter 4 Configuration Logical Drives Tab (New Configuration) The Logical Drives tab in Manual Configuration is where you configure the disk arrays into logical drives. Your first logical drive will set the stripe size and cache line size for all logical drives on this controller. See Figure 4-42. Figure 4-42. Manual Configuration - Logical Drives To configure the Logical Drives, perform the following steps: 1. Select a RAID level for the first logical drive. Supported RAID levels are RAID 0, RAID 1, RAID 3, RAID 5, RAID 0+1, and stand-alone drive (JBOD). Only RAID levels compatible with the current configuration will be available in the list. 2. Enter the amount of available logical or physical capacity for this logical drive. If the total configuration will have only one logical drive, which uses all available capacity, the default sizes should not be changed. 3. If you intend to create additional logical drives now or later, enter a smaller number to reserve the desired amount of capacity. 78

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
Chapter 4
Configuration
78
Logical Drives Tab (New Configuration)
The Logical Drives tab in Manual Configuration is where you configure the disk
arrays into logical drives. Your first logical drive will set the stripe size and cache
line size for all logical drives on this controller. See Figure 4-42.
Figure 4-42. Manual Configuration - Logical Drives
To configure the Logical Drives, perform the following steps:
1.
Select a RAID level for the first logical drive.
Supported RAID levels are RAID 0, RAID 1, RAID 3, RAID 5, RAID
0+1, and stand-alone drive (JBOD).
Only RAID levels compatible with the current configuration will be
available in the list.
2.
Enter the amount of available logical or physical capacity for this logical
drive.
If the total configuration will have only one logical drive, which uses all
available capacity, the default sizes should not be changed.
3.
If you intend to create additional logical drives now or later, enter a smaller
number to reserve the desired amount of capacity.