HP LH4r HP Netserver LH 3/r and LH 4/r Mass Storage Kit - Page 28

Step 6, Install SCSI Cable

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 28 highlights

Chapter 2 Installation 2. Remove Fan Assemblies 0 and 1, as follows: a. Press firmly on the catch in the top of one fan assembly, shown in Figure 2-14, and swing the upper side of the fan assembly away from the accessory board guide. b. Pull the fan assembly gently upward to disengage its prongs on the far side of the fan assembly. Remove the fan assembly from the NetServer. c. Repeat actions a. and b. for the other fan assembly. Step 6: Install SCSI Cable Install the SCSI cable supplied with the kit, as follows: 1. Gently pull aside the cables for the flexible disk drive and CD-ROM drive to gain access to the SCSI B connector on the I/O board, which is shown in Figure 2-15. SCSI B SE Connector (For Non-Hot-Swap Drives Only) SCSI B Connector SCSI Cable Connector Labeled "To I/O Board" I/O Board Figure 2-15. Connect SCSI Cable to I/O Board's SCSI B Connector 2. Connect the SCSI cable's 68-pin connector labeled "To I/O Board" to the SCSI B connector on the I/O board, as shown in Figure 2-15. 24

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
Chapter 2
Installation
24
2.
Remove Fan Assemblies 0 and 1, as follows:
a.
Press firmly on the catch in the top of one fan assembly, shown in
Figure 2-14, and swing the upper side of the fan assembly away from
the accessory board guide.
b.
Pull the fan assembly gently upward to disengage its prongs on the far
side of the fan assembly. Remove the fan assembly from the NetServer.
c.
Repeat actions a. and b. for the other fan assembly.
Step 6:
Install SCSI Cable
Install the SCSI cable supplied with the kit, as follows:
1.
Gently pull aside the cables for the flexible disk drive and CD-ROM drive
to gain access to the SCSI B connector on the I/O board, which is shown in
Figure 2-15.
SCSI B
Connector
SCSI B SE Connector
(For Non-Hot-Swap Drives Only)
SCSI Cable
Connector Labeled
"To I/O Board"
I/O Board
Figure 2-15. Connect SCSI Cable to I/O Board’s SCSI B Connector
2.
Connect the SCSI cable’s 68-pin connector labeled "To I/O Board" to the
SCSI B connector on the I/O board, as shown in Figure 2-15.