HP LH4r HP Netserver LH 3/r and LH 4/r Mass Storage Kit - Page 53

Run Symbios Configuration Utility

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 53 highlights

Chapter 3 Configure Mass Storage 6. On the Configuration menu, use the up and down arrows to highlight "Boot Device Ordering," and press ENTER to choose it. 7. On the Boot Device Ordering submenu, use the up and down arrows to highlight "Boot Device Priority," and press ENTER to choose it. Verify the priorities of the different types of devices. If you need to change the priorities, follow the on-screen instructions. When the boot device priorities are correct, press ESC to return to the Boot Device Ordering submenu. 8. On the Boot Device Ordering submenu, use the up and down arrows to highlight "Hard Drive Priority," and press ENTER to choose it. Verify the priorities of the different types hard drive controllers. If you need to change the priorities, follow the on-screen instructions. When the hard drive priorities are correct, press ESC to return to the Boot Device Ordering submenu. Exit Setup Utility 9. Press the F10 function key to save and exit. 10. In the Setup Confirmation dialog box, press ENTER to answer "Yes" to the question, "Save configuration changes and exit now?" The HP NetServer will restart. Run Symbios Configuration Utility NOTE Use this procedure to do the following: • To verify that devices on all non-RAID SCSI channels are displayed on the boot screen. • To verify that the controllers of all non-RAID SCSI channels are set "On" to operate. • To verify that all non-RAID SCSI channels are searched for a bootable drive. • To control the order in which two non-RAID SCSI channels are searched for a bootable drive. 1. Restart the HP NetServer. 49

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
Chapter 3
Configure Mass Storage
49
6.
On the Configuration menu, use the up and down arrows to highlight "Boot
Device Ordering," and press ENTER to choose it.
7.
On the Boot Device Ordering submenu, use the up and down arrows to
highlight "Boot Device Priority," and press ENTER to choose it. Verify the
priorities of the different types of devices.
If you need to change the priorities, follow the on-screen instructions.
When the boot device priorities are correct, press ESC to return to the Boot
Device Ordering submenu.
8.
On the Boot Device Ordering submenu, use the up and down arrows to
highlight "Hard Drive Priority," and press ENTER to choose it. Verify the
priorities of the different types hard drive controllers.
If you need to change the priorities, follow the on-screen instructions.
When the hard drive priorities are correct, press ESC to return to the Boot
Device Ordering submenu.
Exit Setup Utility
9.
Press the F10 function key to save and exit.
10.
In the Setup Confirmation dialog box, press ENTER to answer "Yes" to the
question, "Save configuration changes and exit now?" The HP NetServer
will restart.
Run Symbios Configuration Utility
NOTE
Use this procedure to do the following:
•
To verify that devices on all non-RAID SCSI channels are
displayed on the boot screen.
•
To verify that the controllers of all non-RAID SCSI
channels are set "On" to operate.
•
To verify that all non-RAID SCSI channels are searched
for a bootable drive.
•
To control the order in which two non-RAID SCSI
channels are searched for a bootable drive.
1.
Restart the HP NetServer.