HP LH4r Integrated HP NetRaid Controller Configuration Guide - Page 101

Integrated HP NetRAID, Enable, Included SCSI_A Channel, Included SCSI_B Channel, Drive roaming done

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 101 highlights

Chapter 9 Configuring a Second Integrated HP NetRAID Channel 6. Enable HP NetRAID on SCSI A using the Setup (F2) utility. See "Step D. Enable Integrated HP NetRAID Controller" in this guide for complete instructions. ◊ Integrated HP NetRAID should be set to Enable. ◊ Included SCSI_A Channel should be set to Yes. ◊ Included SCSI_B Channel should be set to Yes. 7. Boot the HP NetServer Navigator CD-ROM. You will see the following message indicating that the drive roaming feature has moved your existing physical drives from Channel 0 to Channel 1: Drive roaming done. 8. When the NetServer Navigator Main Menu appears, exit and turn off the power to the HP NetServer. 9. Insert the drives that you removed in Step 5. These drives are connected to SCSI A which has just been enabled for HP NetRAID. 10. Boot the HP NetServer Navigator CD-ROM again. You will see the following message: New drives found. Configuration updated. 11. Launch HP NetRAID Assistant, following the instructions in "Step E" in Chapter 5. 12. From the HP NetRAID Assistant main window, verify that your existing hard disk drive information is correct. The drives with your existing data have now moved to Channel 1 and their status should be "Online." The new drives are now on Channel 0 and their status should be "Ready." 13. Select the Configuration menu, and then choose Wizard. CAUTION Do not clear your configuration! You don't need to change the configuration of your existing HP NetRAID channel. 14. Choose either Custom or Automatic mode and define arrays, hot spares, and logical drives on your second channel. Automatic mode will not affect your existing configuration. For complete instructions on configuring arrays and logical drives, see "Step F" in Chapter 5 of this guide. 15. Save your configuration and initialize your new logical drives as described in "Step G" in Chapter 5 of this guide. Exit HP NetRAID Assistant. 95

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
Chapter 9
Configuring a Second Integrated HP NetRAID Channel
95
6.
Enable HP NetRAID on SCSI A using the Setup (F2) utility. See "Step D.
Enable Integrated HP NetRAID Controller" in this guide for complete
instructions.
◊
Integrated HP NetRAID
should be set to
Enable
.
◊
Included SCSI_A Channel
should be set to
Yes
.
◊
Included SCSI_B Channel
should be set to
Yes
.
7.
Boot the
HP NetServer Navigator CD-ROM
. You will see the following
message indicating that the drive roaming feature has moved your
existing physical drives from Channel 0 to Channel 1:
Drive roaming done.
8.
When the NetServer Navigator Main Menu appears, exit and turn off the
power to the HP NetServer.
9.
Insert the drives that you removed in Step 5. These drives are connected to
SCSI A which has just been enabled for HP NetRAID.
10.
Boot the
HP NetServer Navigator CD-ROM
again. You will see the
following message:
New drives found. Configuration updated.
11.
Launch HP NetRAID Assistant, following the instructions in "Step E" in
Chapter 5.
12.
From the HP NetRAID Assistant main window, verify that your existing
hard disk drive information is correct. The drives with your existing data
have now moved to Channel 1 and their status should be "Online." The
new drives are now on Channel 0 and their status should be "Ready."
13.
Select the
Configuration
menu, and then choose
Wizard
.
CAUTION
Do not clear your configuration! You don't need to change
the configuration of your existing HP NetRAID channel.
14.
Choose either
Custom
or
Automatic
mode and define arrays, hot spares,
and logical drives on your second channel. Automatic mode will
not
affect
your existing configuration. For complete instructions on configuring
arrays and logical drives, see "Step F" in Chapter 5 of this guide.
15.
Save your configuration and initialize your new logical drives as described
in "Step G" in Chapter 5 of this guide. Exit HP NetRAID Assistant.