HP LH4r Integrated HP NetRaid Controller Configuration Guide - Page 58

Preview Configuration

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 58 highlights

Chapter 5 Configuration 1. Click the Span Arrays box to mark it with a check. An array labeled with a hyphenated number, such as A0-1 or A0-3, appears in the Logical Devices box. 2. If you know the exact size of the logical drive you want, enter it in the Size (MB) box. If you do not specify the size of the logical drive, the default size reflects the maximum number of arrays that can be spanned. 3. Define the logical drive as described above. To remove the last logical drive that was added: 1. Click the Undo button. 2. You can continue undoing logical drives by clicking Undo. When you are done defining logical drives: • When all the logical drives are defined and you have clicked the Accept button for the last one, click the Next button. The Next button does not operate until one of the following conditions has been satisfied: ◊ All capacity has been assigned to logical drives. ◊ Eight logical drives have been defined. Preview Configuration NOTE Refer to Worksheets A and B when checking the configuration. The HP NetRAID Assistant Wizard Configuration Preview window, shown in Figure 5-6, displays the configuration proposed for the physical and logical drives. 52

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
Chapter 5
Configuration
52
1.
Click the
Span Arrays
box to mark it with a check. An array labeled with
a hyphenated number, such as A0-1 or A0-3, appears in the Logical
Devices box.
2.
If you know the exact size of the logical drive you want, enter it in the
Size (MB) box.
If you do not specify the size of the logical drive, the default size reflects
the maximum number of arrays that can be spanned.
3.
Define the logical drive as described above.
To remove the last logical drive that was added:
1.
Click the
Undo
button.
2.
You can continue undoing logical drives by clicking Undo.
When you are done defining logical drives:
•
When all the logical drives are defined and you have clicked the Accept
button for the last one, click the
Next
button.
The Next button does not operate until one of the following conditions has
been satisfied:
◊
All capacity has been assigned to logical drives.
◊
Eight logical drives have been defined.
Preview Configuration
NOTE
Refer to Worksheets A and B when checking the
configuration.
The HP NetRAID Assistant Wizard Configuration Preview window, shown in
Figure 5-6, displays the configuration proposed for the physical and logical
drives.