HP LH4r Integrated HP NetRaid Controller Configuration Guide - Page 68

Step L. Run HP NetRAID Express Tools optional

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 68 highlights

Chapter 6 HP NetRAID Software Novell NetWare 3.2 1. Exit to the DOS prompt. 2. Insert the diskette called "NetRAID Utilities for NetWare." 3. Type Copy :\NetRAID\*.* :\server.312, where is the drive letter for the diskette drive and is the hard disk where NetWare is installed. Press Enter. 4. To load the HP NetRAID Config utility, type load :\nwserver\megamgr.nlm and press Enter at the NetWare command prompt. Step L. Run HP NetRAID Express Tools (optional) After you have installed your software, you might need to run the HP NetRAID Express Tools utility. Run HP NetRAID Express Tools if you need to do either of the following: • Set the SCSI transfer rate if you are using either Fast/Wide or Ultra/Wide devices with an external connection. The default SCSI transfer rate is Ultra2, so you do not need to set the SCSI transfer rate if you are using internal hot-swap mass storage only. • Disable the HP NetRAID BIOS to prevent booting from the HP NetRAID subsystem. HP NetRAID Express Tools is a configuration and management utility that resides in a chip on the HP NetServer I/O board along with the HP NetRAID BIOS and firmware. For more information about HP NetRAID Express Tools and its functions, refer to the HP NetRAID Series User Guide in Information Assistant. To start HP NetRAID Express Tools: 1. Boot the host HP NetServer and watch for the flashing message: Option: Experienced users may press for HP NetRAID Express Tools now. Firmware Initializing 2. While this message is flashing, press or . When the system stops scanning, HP NetRAID Express Tools starts and displays the Tools Management menu. 62

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
Chapter 6
HP NetRAID Software
62
Novell NetWare 3.2
1.
Exit to the DOS prompt.
2.
Insert the diskette called "NetRAID Utilities for NetWare."
3.
Type
Copy <d1>:\NetRAID\*.* <d2>:\server.312
, where
<d1>
is the drive letter for the diskette drive and
<d2>
is the hard disk
where NetWare is installed. Press Enter.
4.
To load the HP NetRAID Config utility, type
load <d2>:\nwserver\megamgr.nlm
and press Enter at the
NetWare command prompt.
Step L. Run HP NetRAID Express Tools (optional)
After you have installed your software, you might need to run the HP NetRAID
Express Tools utility. Run HP NetRAID Express Tools if you need to do either of
the following:
•
Set the SCSI transfer rate if you are using either Fast/Wide or Ultra/Wide
devices with an external connection. The default SCSI transfer rate is
Ultra2, so you do
not
need to set the SCSI transfer rate if you are using
internal hot-swap mass storage only.
•
Disable the HP NetRAID BIOS to prevent booting from the HP NetRAID
subsystem.
HP NetRAID Express Tools is a configuration and management utility that
resides in a chip on the HP NetServer I/O board along with the HP NetRAID
BIOS and firmware. For more information about HP NetRAID Express Tools and
its functions, refer to the
HP NetRAID Series User Guide
in Information
Assistant.
To start HP NetRAID Express Tools:
1.
Boot the host HP NetServer and watch for the flashing message:
Option: Experienced users may press <Ctrl> <m> for
HP NetRAID Express Tools now.
Firmware Initializing
2.
While this message is flashing, press <Ctrl> <M> or <Ctrl> <m>. When
the system stops scanning, HP NetRAID Express Tools starts and displays
the Tools Management menu.