HP LH4r Integrated HP NetRaid Controller Configuration Guide - Page 45

Configuration

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 45 highlights

5 Configuration Overview This chapter covers Steps C, D, E, F, and G of the installation procedure. You should already have completed Step A, "Plan Your Hardware," and Step B, "Plan Arrays and Logical Drives" in Chapter 4. Step C. Verify Hardware Setup Verify that your hardware setup matches the plans you sketched in Worksheet A. Make sure that: • Disk drive modules are inserted in the hot-swap mass storage cage • You have installed a second mass storage cage, or you have connected an external mass storage enclosure, if you are planning to use two channels • SCSI IDs are set NOTE Make sure the SCSI IDs of the non-hot-swap devices do not conflict with the SCSI IDs of the hot-swap disk drive modules connected to SCSI B. Step D. Enable Integrated HP NetRAID Controller The HP NetServer LH 3 and LH 3r factory default setting enables the integrated HP NetRAID controller for the SCSI A port only. Use the Setup utility to verify this setting, or to enable the integrated HP NetRAID controller for the SCSI B port as well. 39

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
39
5
Configuration
Overview
This chapter covers Steps C, D, E, F, and G of the installation procedure. You
should already have completed Step A, "Plan Your Hardware," and Step B, "Plan
Arrays and Logical Drives" in Chapter 4.
Step C.
Verify Hardware Setup
Verify that your hardware setup matches the plans you sketched in Worksheet A.
Make sure that:
•
Disk drive modules are inserted in the hot-swap mass storage cage
•
You have installed a second mass storage cage, or you have connected an
external mass storage enclosure, if you are planning to use two channels
•
SCSI IDs are set
NOTE
Make sure the SCSI IDs of the non-hot-swap devices do not
conflict with the SCSI IDs of the hot-swap disk drive modules
connected to SCSI B.
Step D. Enable Integrated HP NetRAID Controller
The HP NetServer LH 3 and LH 3r factory default setting enables the integrated
HP NetRAID controller for the SCSI A port only. Use the Setup utility to verify
this setting, or to enable the integrated HP NetRAID controller for the SCSI B
port as well.