HP LH4r Integrated HP NetRaid Controller Configuration Guide - Page 67

Step K., Install NOS-specific Configuration Utility

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 67 highlights

Chapter 6 HP NetRAID Software Step K. Install NOS-specific Configuration Utility In this step, you install the configuration utility specific to Windows NT or Novell NetWare. • If you are using Microsoft Windows NT, you install the HP NetRAID Assistant utility. This is the Windows NT version of the utility you used to configure your system in Chapter 5. • If you are using Novell NetWare, you install the HP NetRAID Config utility for NetWare. Chapter 10, "Understanding HP NetRAID Utilities," has menu maps of both of these utilities. For complete information about these utilities, see the HP NetRAID Series User Guide in Information Assistant. Install the utility as described for the NOS version below. Microsoft Windows NT 4.0 1. Select Start from the taskbar. 2. Choose Run from the Start menu. 3. Insert diskette #1, "NetRAID Assistant for WindowsNT and Windows95." 4. Type :\setup at the Open: prompt, where is the drive letter of the diskette drive you are using. 5. Follow the on-screen instructions. Novell NetWare 4.11, 4.11 SMP, SFTIII 4.11 1. Exit to the DOS prompt. 2. Insert the diskette called "NetRAID Utilities for NetWare." 3. Type Copy :\NetRAID\*.* :\nwserver, where is the drive letter for the diskette drive and is the hard disk where NetWare is installed. Press Enter. 4. To load the HP NetRAID Config utility, type load :\nwserver\megamgr.nlm and press Enter at the NetWare command prompt. 61

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
Chapter 6
HP NetRAID Software
61
Step K.
Install NOS-specific Configuration Utility
In this step, you install the configuration utility specific to Windows NT or
Novell NetWare.
•
If you are using Microsoft Windows NT, you install the HP NetRAID
Assistant utility. This is the Windows NT version of the utility you used to
configure your system in Chapter 5.
•
If you are using Novell NetWare, you install the HP NetRAID Config
utility for NetWare.
Chapter 10, "Understanding HP NetRAID Utilities," has menu maps of both of
these utilities. For complete information about these utilities, see the
HP NetRAID Series User Guide
in Information Assistant.
Install the utility as described for the NOS version below.
Microsoft Windows NT 4.0
1.
Select
Start
from the taskbar.
2.
Choose
Run
from the Start menu.
3.
Insert diskette #1, "NetRAID Assistant for WindowsNT and Windows95."
4.
Type
<d>:\setup
at the Open: prompt, where
<d>
is the drive letter of
the diskette drive you are using.
5.
Follow the on-screen instructions.
Novell NetWare 4.11, 4.11 SMP, SFTIII 4.11
1.
Exit to the DOS prompt.
2.
Insert the diskette called "NetRAID Utilities for NetWare."
3.
Type
Copy <d1>:\NetRAID\*.* <d2>:\nwserver
, where
<d1>
is the drive letter for the diskette drive and
<d2>
is the hard disk where
NetWare is installed. Press Enter.
4.
To load the HP NetRAID Config utility, type
load <d2>:\nwserver\megamgr.nlm
and press Enter at the
NetWare command prompt.