HP OfficeJet Pro 8210 User Guide - Page 64

Solve paper-feed problems, Paper is not picked up from a tray, s are skewing

Page 64 highlights

● Prevent curled or wrinkled paper by storing all unused paper flat in a resealable bag. ● Do not use paper that is too thick or too thin for the printer. ● Make sure that the trays are loaded correctly and are not too full. For more information, see Load paper. ● Ensure that paper loaded in the input tray lays flat and the edges are not bent or torn. ● Do not combine different paper types and paper sizes in the input tray; the entire stack of paper in the input tray must be the same size and type. ● Adjust the paper-width guides in the input tray to fit snugly against all paper. Make sure the paper-width guides do not bend the paper in the input tray. ● Use paper types that are recommended for the printer. ● If the printer is about to run out of paper, allow the printer to run out of paper first, and then add paper. Do not load paper when the printer is printing. ● When removing the input tray, it is recommended to remove the tray completely from the printer to make sure no paper is stuck at the rear of the tray. Solve paper-feed problems What kind of problem are you having? ● Paper is not picked up from a tray - Make sure paper is loaded in the tray. For more information, see Load paper. Fan the paper before loading. - Make sure the paper-width guides are set to the correct markings in the tray for the paper size you are loading. Also make sure the paper guides are snug, but not tight, against the stack. - Ensure that the stack of paper is aligned with the appropriate paper size lines on the bottom of the input tray, and does not exceed the stack height indicated by one or more label on the side or paper-width guide of the input tray. - Make sure paper in the tray is not curled. Uncurl paper by bending it in the opposite direction of the curl. ● Pages are skewing - Make sure the paper loaded in the input tray is aligned to the paper-width guides. If needed, pull out the input tray from the printer and reload the paper correctly, making sure that the paper guides are aligned correctly. - Load paper into the printer only when it is not printing. ● Multiple pages are being picked up - Make sure the paper-width guides are set to the correct markings in the tray for the paper size you are loading. Also make sure the paper-width guides are snug, but not tight, against the stack. - Ensure that the stack of paper is aligned with the appropriate paper size lines on the bottom of the input tray, and does not exceed the stack height indicated by one or more label on the side or paper-width guide of the input tray. - Make sure the tray is not overloaded with paper. - Use HP paper for optimum performance and efficiency. 58 Chapter 8 Solve a problem ENWW

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95

Prevent curled or wrinkled paper by storing all unused paper
flat
in a resealable bag.
Do not use paper that is too thick or too thin for the printer.
Make sure that the trays are loaded correctly and are not too full. For more information, see
Load paper.
Ensure that paper loaded in the input tray lays
flat
and the edges are not bent or torn.
Do not combine
different
paper types and paper sizes in the input tray; the entire stack of paper in the
input tray must be the same size and type.
Adjust the paper-width guides in the input tray to
fit
snugly against all paper. Make sure the paper-width
guides do not bend the paper in the input tray.
Use paper types that are recommended for the printer.
If the printer is about to run out of paper, allow the printer to run out of paper
first,
and then add paper.
Do not load paper when the printer is printing.
When removing the input tray, it is recommended to remove the tray completely from the printer to
make sure no paper is stuck at the rear of the tray.
Solve paper-feed problems
What kind of problem are you having?
Paper is not picked up from a tray
Make sure paper is loaded in the tray. For more information, see
Load paper. Fan the paper before
loading.
Make sure the paper-width guides are set to the correct markings in the tray for the paper size you
are loading. Also make sure the paper guides are snug, but not tight, against the stack.
Ensure that the stack of paper is aligned with the appropriate paper size lines on the bottom of the
input tray, and does not exceed the stack height indicated by one or more label on the side or
paper-width guide of the input tray.
Make sure paper in the tray is not curled. Uncurl paper by bending it in the opposite direction of the
curl.
Pages are skewing
Make sure the paper loaded in the input tray is aligned to the paper-width guides. If needed, pull
out the input tray from the printer and reload the paper correctly, making sure that the paper
guides are aligned correctly.
Load paper into the printer only when it is not printing.
Multiple pages are being picked up
Make sure the paper-width guides are set to the correct markings in the tray for the paper size you
are loading. Also make sure the paper-width guides are snug, but not tight, against the stack.
Ensure that the stack of paper is aligned with the appropriate paper size lines on the bottom of the
input tray, and does not exceed the stack height indicated by one or more label on the side or
paper-width guide of the input tray.
Make sure the tray is not overloaded with paper.
Use HP paper for optimum performance and
efficiency.
58
Chapter 8
Solve a problem
ENWW