HP P6300 HP P6300/P6500 EVA Installation Guide (5697-2485, September 2013) - Page 17

System and performance expectations, RAID levels, The EVA has four Vraid types: Vraid0, Vraid1

Get HP P6300 PDF manuals and user guides View all HP P6300 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

5. Enable CHAP for the Microsoft iSCSI initiator running on the iSCSI server: a. Click the General tab. b. Click Secret in the middle of the screen. c. Click Reset. d. Enter the iSCSI or iSCSI/FCoE presented target CHAP secret. For example: hpstorage. e. Click OK. f. Click the Discovery tab and when manually discovering iSCSI target portals: i. Click Add under Target Portals. ii. Enter the IP address of the iSCSI port of the 1 GbE iSCSI modules or the 10GbE iSCSI/FCoE modules. iii. Click Advanced. iv. Select the CHAP Login Information check box. v. Enter the CHAP secret for the 1 GbE iSCSI modules or the 10GbE iSCSI/FCoE modules discovered iSCSI initiator in the Target Secret box, for example, CHAPsecret01. vi. Select the Mutual Authentication check box. vii. Click OK twice and the initiator completes target discovery. g. Click Targets and select the appropriate target for login. h. Click Log On and then click Advanced. i. Select the CHAP Login Information check box. j. Enter the CHAP secret for the discovered iSCSI initiator of the iSCSI or iSCSI/FCoE modules in the Target Secret box, for example, CHAPsecret01. k. Select the Mutual Authentication check box. l. Click OK twice, and the initiator completes normal login. System and performance expectations To help determine the best way to configure your storage, rank the following three storage characteristics in order of importance: • Fault tolerance (high availability) • I/O performance • Storage efficiency With your priorities established, you can determine which striping method and RAID level to use. As highlighted in the following section, some configuration methods offer greater fault tolerance, while other configuration methods offer better I/O performance or storage efficiency. RAID levels Vraid is the HP term for the implementation of RAID storage on EVAs. Vraid is also referred to as redundancy in HP management software. Virtual disks with HP Vraid use three key RAID methods: data striping, data mirroring, and parity error checking. Unlike traditional RAID, all HP Vraid levels distribute data across all available physical disks. Data striping improves speed by performing virtual disk I/O with an entire group of physical disks at the same time. Mirroring provides data redundancy by storing data and a copy of the data. Parity also provides data redundancy by storing data and the calculated parity for each stripe of data. If a subset of the data on a physical disk becomes corrupt or the entire physical disk fails, the data can be automatically recovered from redundancy so that data loss does not occur. The EVA has four Vraid types: Vraid0, Vraid1, Vraid5, and Vraid6. Each Vraid type provides unique I/O speed and has a different level of data redundancy, which directly effects the amount of physical space used. Once a virtual disk is created, the Vraid type or level cannot be changed. Plan your storage configuration 17

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
5.
Enable CHAP for the Microsoft iSCSI initiator running on the iSCSI server:
a.
Click the
General
tab.
b.
Click
Secret
in the middle of the screen.
c.
Click
Reset
.
d.
Enter the iSCSI or iSCSI/FCoE presented target CHAP secret. For example: hpstorage.
e.
Click
OK
.
f.
Click the
Discovery
tab and when manually discovering iSCSI target portals:
i.
Click
Add
under Target Portals.
ii.
Enter the IP address of the iSCSI port of the 1 GbE iSCSI modules or the 10GbE
iSCSI/FCoE modules.
iii.
Click
Advanced
.
iv.
Select the
CHAP Login Information
check box.
v.
Enter the CHAP secret for the 1 GbE iSCSI modules or the 10GbE iSCSI/FCoE
modules discovered iSCSI initiator in the Target Secret box, for example,
CHAPsecret01.
vi.
Select the
Mutual Authentication
check box.
vii.
Click
OK
twice and the initiator completes target discovery.
g.
Click
Targets
and select the appropriate target for login.
h.
Click
Log On
and then click
Advanced
.
i.
Select the
CHAP Login Information
check box.
j.
Enter the CHAP secret for the discovered iSCSI initiator of the iSCSI or iSCSI/FCoE
modules in the Target Secret box, for example, CHAPsecret01.
k.
Select the
Mutual Authentication
check box.
l.
Click
OK
twice, and the initiator completes normal login.
System and performance expectations
To help determine the best way to configure your storage, rank the following three storage
characteristics in order of importance:
•
Fault tolerance (high availability)
•
I/O performance
•
Storage efficiency
With your priorities established, you can determine which striping method and RAID level to use.
As highlighted in the following section, some configuration methods offer greater fault tolerance,
while other configuration methods offer better I/O performance or storage efficiency.
RAID levels
Vraid is the HP term for the implementation of RAID storage on EVAs. Vraid is also referred to as
redundancy
in HP management software. Virtual disks with HP Vraid use three key RAID methods:
data striping, data mirroring, and parity error checking. Unlike traditional RAID, all HP Vraid levels
distribute data across
all
available physical disks.
Data striping improves speed by performing virtual disk I/O with an entire group of physical disks
at the same time. Mirroring provides data redundancy by storing data and a copy of the data.
Parity also provides data redundancy by storing data and the calculated parity for each stripe of
data. If a subset of the data on a physical disk becomes corrupt or the entire physical disk fails,
the data can be automatically recovered from redundancy so that data loss does not occur.
The EVA has four Vraid types: Vraid0, Vraid1, Vraid5, and Vraid6. Each Vraid type provides
unique I/O speed and has a different level of data redundancy, which directly effects the amount
of physical space used. Once a virtual disk is created, the Vraid type or level cannot be changed.
Plan your storage configuration
17