HP P6300 HP P6300/P6500 EVA Installation Guide (5697-2485, September 2013) - Page 52

Restarting the iSCSI or iSCSI/FCoE module

Get HP P6300 PDF manuals and user guides View all HP P6300 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 52 highlights

6. Enter YES in the open dialog box. 7. Select Update. The iSCSI or iSCSI/FCoE module will reboot after it is upgraded. Restarting the iSCSI or iSCSI/FCoE module If you determine that the iSCSI or iSCSI/FCoE modules must be rebooted, you can use HP P6000 Command View to restart the modules. Shutting down the iSCSI or iSCSI/FCoE modules through HP P6000 Command View is not supported. You must use the CLI to shut down the modules and then power cycle the array to power on the modules after the shutdown. To restart a module: 1. Select the iSCSI controller in the Navigation pane. 2. Select Shutdown on the iSCSI Controller Properties window. 3. Select Restart on the iSCSI Controller Shutdown Options window (Figure 42 (page 52)). Figure 42 iSCSI Controller Shutdown Options To shut down an iSCSI or iSCSI/FCoE module using the CLI: 1. Log in to the serial or management port CLI. 2. Log in to the administrator account. 3. Enter the shutdown command. For example: MEZ75 login: guest Password: password Welcome to MEZ75 * * * HP StorageWorks MEZ75 * * * MEZ75 #> admin start Password : ****** MEZ75 (admin) #> shutdown Are you sure you want to shutdown the System (y/n): y Shutdown completed. System is in a state that is ready to be powered off. MEZ75 #> Connection to host lost. NOTE: A shutdown places the iSCSI or iSCSI/FCoE module into a low power sleep state. A wake-up requires a controller power cycle, either by use of the on/off push button or by removing and re-installing the controller. Saving or restoring the iSCSI or iSCSI/FCoE module configuration After the initial setup of the iSCSI or iSCSI/FCoE modules, save the configuration for each module, in case a service action is required. The Save Configuration function (Figure 43 (page 53)) enables you to save the configuration from a selected module to a file on the management server. You can use this file as a restoration point. The Full Configuration Restore function enables the restoration of the configuration to the point when the configuration was last saved (such as during the LUN 52 Managing the iSCSI or iSCSI/FCoE module using HP P6000 Command View

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
6.
Enter
YES
in the open dialog box.
7.
Select
Update
.
The iSCSI or iSCSI/FCoE module will reboot after it is upgraded.
Restarting the iSCSI or iSCSI/FCoE module
If you determine that the iSCSI or iSCSI/FCoE modules must be rebooted, you can use HP P6000
Command View to restart the modules. Shutting down the iSCSI or iSCSI/FCoE modules through
HP P6000 Command View is not supported. You must use the CLI to shut down the modules and
then power cycle the array to power on the modules after the shutdown.
To restart a module:
1.
Select the iSCSI controller in the Navigation pane.
2.
Select
Shutdown
on the iSCSI Controller Properties window.
3.
Select
Restart
on the iSCSI Controller Shutdown Options window (
Figure 42 (page 52)
).
Figure 42 iSCSI Controller Shutdown Options
To shut down an iSCSI or iSCSI/FCoE module using the CLI:
1.
Log in to the serial or management port CLI.
2.
Log in to the administrator account.
3.
Enter the
shutdown
command. For example:
MEZ75 login: guest
Password: password
Welcome to MEZ75
******************************************************
*
*
*
HP StorageWorks MEZ75
*
*
*
******************************************************
MEZ75 #> admin start
Password
:
******
MEZ75 (admin) #> shutdown
Are you sure you want to shutdown the System (y/n):
y
Shutdown completed.
System is in a state that is ready to be powered off.
MEZ75 #>
Connection to host lost.
NOTE:
A shutdown places the iSCSI or iSCSI/FCoE module into a low power sleep state.
A wake-up requires a controller power cycle, either by use of the on/off push button or by
removing and re-installing the controller.
Saving or restoring the iSCSI or iSCSI/FCoE module configuration
After the initial setup of the iSCSI or iSCSI/FCoE modules, save the configuration for each module,
in case a service action is required. The Save Configuration function (
Figure 43 (page 53)
) enables
you to save the configuration from a selected module to a file on the management server. You can
use this file as a restoration point. The Full Configuration Restore function enables the restoration
of the configuration to the point when the configuration was last saved (such as during the LUN
52
Managing the iSCSI or iSCSI/FCoE module using HP P6000 Command View