HP P6300 HP P6300/P6500 EVA Installation Guide (5697-2485, September 2013) - Page 38

iSCSI/FCoE module management ports and P6000 fabrics

Get HP P6300 PDF manuals and user guides View all HP P6300 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 38 highlights

Figure 22 iSCSI/FCoE module management ports and P6000 fabrics 1. Fibre Channel fabric A 2. Fibre Channel fabric B 3. iSCSI/FCoE fabric A 4. iSCSI/FCoE fabric B 5. RS232 management ports 6. Telnet management ports The following is an example of using the CLI to configure the telnet management port with a static IPv4 address: CLI example of: login set mgmt show mgmt help MEZ75 login: guest Password: password Welcome to MEZ75 * * * HP StorageWorks MEZ75 * * * MEZ75 #> admin start -p config MEZ75 (admin) #> set mgmt A list of attributes with formatting and current values will follow. Enter a new value or simply press the ENTER key to accept the current value. If you wish to terminate this process before reaching the end of the list press 'q' or 'Q' and the ENTER key to do so. WARNING: The following command might cause a loss of connections to the MGMT port. IPv4 Interface (0=Enable, 1=Disable) IPv4 Mode (0=Static, 1=DHCP, 2=Bootp, 3=Rarp) IPv4 Address IPv4 Subnet Mask IPv4 Gateway IPv6 Interface (0=Enable, 1=Disable) [Enabled [Static [0.0.0.0 [0.0.0.0 [0.0.0.0 [Disabled ] 0 ] 0 ] 10.6.6.130 ] 255.255.140.0 ] 10.6.4.201 ] All attribute values that have been changed will now be saved. MEZ75 (admin) #> show mgmt Management Port Information 38 Managing the iSCSI or iSCSI/FCoE module using HP P6000 Command View

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
Figure 22 iSCSI/FCoE module management ports and P6000 fabrics
4. iSCSI/FCoE fabric B
1. Fibre Channel fabric A
5. RS232 management ports
2. Fibre Channel fabric B
6. Telnet management ports
3. iSCSI/FCoE fabric A
The following is an example of using the CLI to configure the telnet management port with a static
IPv4 address:
CLI example of: login
set mgmt
show mgmt
help
MEZ75 login: guest
Password: password
Welcome to MEZ75
******************************************************
*
*
*
HP StorageWorks MEZ75
*
*
*
******************************************************
MEZ75 #> admin start
–
p config
MEZ75 (admin) #> set mgmt
A list of attributes with formatting and current values will follow.
Enter a new value or simply press the ENTER key to accept the current value.
If you wish to terminate this process before reaching the end of the list
press 'q' or 'Q' and the ENTER key to do so.
WARNING:
The following command might cause a loss of connections to the MGMT port.
IPv4 Interface (0=Enable, 1=Disable)
[Enabled
] 0
IPv4 Mode (0=Static, 1=DHCP, 2=Bootp, 3=Rarp)
[Static
] 0
IPv4 Address
[0.0.0.0
] 10.6.6.130
IPv4 Subnet Mask
[0.0.0.0
] 255.255.140.0
IPv4 Gateway
[0.0.0.0
] 10.6.4.201
IPv6 Interface (0=Enable, 1=Disable)
[Disabled
]
All attribute values that have been changed will now be saved.
MEZ75 (admin) #> show mgmt
Management Port Information
-----------------------------
38
Managing the iSCSI or iSCSI/FCoE module using HP P6000 Command View